Related Manuals for LG Mono X Plus Series
Summary of Contents for LG Mono X Plus Series
- Page 1 Installation manual PV SOLAR MODULE PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING YOUR SET AND RETAIN IT FOR FUTURE REFERENCE P-TYPE MODELS N-TYPE MODELS LGXXXS1C(W)-A5 LGXXXN1C(W,K)-A5 LGXXXS2W-A5 LGXXXN2C(W,K)-A5 www.lg-solar.com/uk...
-
Page 2: Table Of Contents
CONTENTS 1. Safety 2. Before & After Installation 3. Electrical Installation 4. Mechanical Installation 5. Product Speciications 6. Disclaimer of Liability / Disposal 7. Transporting and Storage 8. Appendix REVISIONS TABLE Date Version Description of change Remark 2016.09.27 1.0 (1st edition) 2016.11.30 Add N-Type Products Add P-Type Product (302W) -
Page 3: Safety
1. SAFETY The instructions related to the safety indicated in the following are for preventing unexpected danger or damage in advance by safely and exactly using the product. Non-compliance of the instructions may immediately cause serious injury or death. Non-compliance of the instructions may cause death or serious injury to the user. Non-compliance of the instructions may cause injury or property damage to the user. - Page 4 1. SAFETY 1. P lease use proper equipment, connector, wire and buttress for system coniguration of the module. It may result in damage or failure of the product. 2. Do not perform installation in rainy, heavily windy or snowy days. It may result in safety accident. 3. Do not make holes in the frame or glass of the module. It may decrease the strength of the frame or break the glass.
-
Page 5: Before & After Installation
• Dirt build-up on the surface of the panel can cause active solar cells to be shaded and electrical performance to be impaired. • Always keep the back surface of the panel free from any foreign objects or structural elements which could come into contact with the panel, especially when the panel is under mechanical load. • F or permission to use mounting methods not described in the Mounting Guide please consult LG Solar. Failure to do so will void the warranty and panel certiication. - Page 6 2. BEFORE & AFTER INSTALLATION After Installation • Plug the connector in tightly and ensure that the wiring properly works. • It is advisable to conduct periodic inspection of the panels for damage to front glass, back sheet, frame, junction box, or external electrical connections.
-
Page 7: Electrical Installation
• The panel contains factory installed bypass diodes located inside the junction box. • When installing the system, it is recommended to install the lightning rod to protect the system. • The junction box should not be opened. Opening the junction box may void the warranty. • P anels with a suspected electrical problem should be returned to LG Electronics for inspection and possible repair or replacement as per the warranty conditions provided by LG Electronics. Electrical Connections • M odules may be connected in series and/or parallel to achieve the desired electrical output as long as certain... - Page 8 • A ll wiring should use a lexible copper (Cu) conductor. • The minimum size should be determined by the applicable codes. • W e recommend a size not smaller than 4 mm². Earth Grounding • T he solar modules from LG Electronics meet the conditions Module frame of safety class II. Therefore grounding is not mandatory. Bolt However grounding is recommended. Also equipotential bonding must be realized.
-
Page 9: Mechanical Installation
4. MECHANICAL INSTALLATION Module Mounting • T he LG Electronics’ (LGE) Limited Warranty for solar modules is contingent upon modules being mounted in accordance with the requirements described in this section. • The solar modules are in Application Class A and have the Safety Class II. Therefore they can be operated in systems with 120 V DC and higher. General access is not restricted. Site Consideration LGE solar modules should be mounted in a location that meets the following requirements. -
Page 10: Product Speciications
The recommended standoff height is a minimum of 100 mm. • W hen installed on a roof, the solar module must be mounted over a ire-resistant roof covering rated for the application. The ire resistance of the solar module from LG Electronics is class C after ANSI/UL790. • The solar module is only IEC listed for use when its factory frame is fully intact. • Do not remove or alter the solar module frame. - Page 11 5. PRODUCT SPECIFICATIONS P-TYPE MODELS Rated electrical characteristic except power rating within -0/+3 percent are within 5 percent of measured. Values at Stand ard Test Condition (STC) : Irradiance 1,000 W/m², Cell temp. 25 °C, 1.5AM Certiicates Electrical Properties Mechanical Properties LG280S1C(W)-A5 MC4/JM601A 0~3 % 37.7 9.87 30.1 9.31 1,000 1,686 1,016 18.0 LG285S1C(W)-A5 MC4/JM601A 0~3 % 38.0 9.92 30.5 9.35 1,000 1,686 1,016 18.0 LG290S1C(W)-A5 MC4/JM601A 0~3 % 38.3 9.97 31.0...
- Page 12 5. PRODUCT SPECIFICATIONS N-TYPE MODELS Rated electrical characteristic except power rating within -0/+3 percent are within 5 percent of measured. Values at Stand ard Test Condition (STC) : Irradiance 1,000 W/m², Cell temp. 25 °C, 1.5AM Certiicates Electrical Properties Mechanical Properties LG305N1C(W)-A5 1,000 MC4/JM601A/05-8 1,686 1,016 0~3 % 40.4 10.25 31.7 9.63 18.0 LG310N1C(W)-A5 1,000 MC4/JM601A/05-8 1,686 1,016 0~3 % 40.5 10.29 32.1 9.67 18.0 LG315N1C(W)-A5 1,000 MC4/JM601A/05-8 1,686 1,016 0~3 % 40.6 10.33...
-
Page 13: Disclaimer Of Liability / Disposal
Disclaimer of Liability • Since the use of this Safety, Installation and Operation instructions and the conditions or methods of installation, operation, use and maintenance of the panel are beyond the control of LG Electronics, LG Electronics does not assume responsibility and expressly disclaims liability for loss, damage, injury or expense arising out of or in any connected with such installation, operation, use or maintenance of the panel. -
Page 14: Appendix
A: 120 mm B: 400 mm Rear: 5,400Pa Rear: 1,800Pa Front: 3,200Pa Front: 6,000Pa 6point ( ①+② ) A: 120 mm C: 120 mm B: 843±100 mm Rear: 1,800Pa Rear: 5,400Pa * 4 point installation is allowed in the following cases: 1. Slope roof: If module is installed parallel to the rooftop. 2. Flat roof: If installed with an additional stand such as wind shield or delector. Note) All mechanical installation method (Fig.1 to Fig.6) in this appendix were not tested by VDE. It is valuated by LG internal test. - Page 15 A: 120 mm B: 400 mm Rear: 4,300Pa Rear: 1,600Pa Front: 3,200Pa Front: 5,400Pa 6point ( ①+② ) A: 120 mm C: 120 mm B: 1,012±100 mm Rear: 1,600Pa Rear: 4,300Pa * 4 point installation is allowed in the following cases: 1. Slope roof: If module is installed parallel to the rooftop. 2. Flat roof: If installed with an additional stand such as wind shield or delector. Note) All mechanical installation method (Fig.1 to Fig.7) and bolting method in this appendix were not tested by VDE. It is valuated by LG internal test.
- Page 16 8. APPENDIX Mechanical Installation: 72Cell Model Fig7. Bolting Type ① Front: 2,000Pa ① : 812 mm Rear: 1,750Pa Note) When installed Fig.7, follow the NEXTracker’s recommended applied torque and materials to fasten the modules. Bolting Method Module frame Bolt Flat washer Mounting Rail Flat washer Spring washer • F our M8(5/16inch) stainless steel bolts, four nuts, four spring washers, and eight lat washers are recommended per solar module. Note) All mechanical installation method(Fig.1 to Fig.7) and bolting method in this appendix were not tested by VDE. It is evaluated by LG internal test.
- Page 17 LG Electronics Deutschland GmbH LG Electronics Inc. This document is subject to change without notice. EU Solar Business Group LG, LG logo and Life's Good are trademarks of LG Electronics, (Global HQ) LG Twin Towers, 128, Inc. worldwide. Trademarks and,intellectual properties of LG Alfred-Herrhausen-Allee 3–5 65760 Eschborn, Germany Electronics, Inc. are protected by international copyright laws. Yeoui-daero, E-Mail: solar@lge.de Yeongdeungpo-gu, www.lg-solar.com/uk Seoul 150-721, Korea Document : II-A5-IEC-V3-EN-201609...