Advertisement
For this reason do not attempt to remove jammed logs by hand. A jammed log is a log which is only partially split and continues to grip
the splitting wedge.
1.5.
SafETy Of OTHERS.
DO NOT allow another person to help you with a jammed log.
8
Keep children and unauthorised persons away from the work area.
9
The log splitter must always be operated by one person only. other people must keep a safe distance from the log splitter especially
9
when it is in operation.
Store the log splitter in a safe area away from children and other people not qualified to use the log splitter.
9
1.6.
GENERaL SafETy.
DO NOT make any modifications to the log splitter.
8
DO NOT exceed the stated log capacity of the log splitter.
8
DO NOT use the log splitter for a task it is not designed to perform.
8
DO NOT leave the log splitter until the splitting wedge has returned to the start position.
8
DO NOT force the log splitter to work beyond its specified capacity.
8
ensure that there are no nails, screws or other foreign objects in logs to be split.
9
The end of logs should be cut square.
9
WaRNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that
‰
may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
2. INTRODucTION
Safe and easy way to split logs, offering continuous sizing and up to 5.5tonne of pressure. Three tier table system and adjustable wedge
allows work-piece to be as near to wedge as possible minimising splitting time. Fitted with a two hand safety operation, twin pull-in and push-
down levers.
3. SPEcIfIcaTION
model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LS1050V
Tier log lengths . . . . . . . . . . . . . . . . . . . . . . . . . . 540, 790, 1050mm
Maximum log diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320mm
Vertical Ram Travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mm
Maximum load Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5ton
Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000W
Overall (W x L x H): . . . . . . . . . . . . . . . . . . . . . . 565 x 840 x 1520mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97kg
4. OPERaTION
(Refer to fig.1 below). The log splitter has an electrically powered hydraulic ram situated inside the lower hollow upright steel section. The ram
is usually fully extended at rest and is connected to the upper hollow steel section behind the splitting wedge (2). When the motor is switched
on and the two control levers are operated the ram retracts and draws the splitting wedge downwards to split the log situated on the table.
4.1.
Serrated Log clamp. Grips log when pressure is applied through the control levers (24).
4.2.
Splitting Wedge. After prolonged use it may be necessary to sharpen the wedge with
a fine toothed file.
4.3.
upper Steel Section (moving). drawn downwards by ram action.
4.4.
adjustable Ram Travel Rod. Controls the ram starting point above the table.
4.5.
upper Transit Handle. Used in conjunction with lower transit handle (8) when unit
is moved
4.6.
Ram Travel Rod Locking Knob. locks ram travel rod when setting ram travel.
4.7.
control levers connection bracket. Transfers the action of the control levers to the
hydraulic system.
4.8.
Lower Transit Handle. Used in conjunction with upper transit handle (8) when unit
is moved
4.9.
mains connector Shield. Protects mains connector from ingress of dust and debris.
4.10.
ON Switch. Starts electric motor.
4.11.
Lower Steel Section (static). Houses the ram.
4.12.
motor. drives pump to power hydraulic system.
4.13.
Pump Housing Guard. Protects pump and hydraulic pipework.
4.14.
Oil Tank cap. Also acts as an air bleed when loosened by several turns.
4.15.
Wheels. only make contact with the ground when the unit is tipped backwards for
transit.
4.16.
Base of unit. ensure that the base is on a level and firm surface to ensure stability
of unit during use.
4.17.
Lower Table Position. ensure that table is fully inserted and hooked into position on
each side of beam.
4.18.
middle Table Position. ensure that table is fully inserted and hooked into position on each side of beam.
4.19.
Table Locking Knob. Screw fully in to lock table in each position.
4.20.
Table. ensure that table is fully inserted and hooked into position on each side of beam.
4.21.
upper Table Position. ensure that table is fully inserted and hooked into position on each side of beam.
4.22.
Off Switch. Stops electric motor.
4.23.
Serrated Log clamp. Grips log when pressure is applied through the control levers (24).
4.24.
control levers. Used to grip the log and initiate the ram movement.
4.25.
control lever guard (Wire). Protects hands when using control levers.
4.26.
control lever shields. Protects hands when using control levers.
© Jack Sealey limited
Original Language Version
fig.1
lS1050V Issue 3 (HF) 25/06/18
Advertisement
