PROMPTS
38
Delay Zn3 (secs)
(00)
Rpt Zn3 ONLY if
39
Armed (N)_
40
Zn4 Trigger Type
(V+)_
41
Invert Zn4 Y/N
(N)_
42
Restore Zn4 Y/N
(Y)_
Delay Zn4 (secs)
43
(00)
Rpt Zn4 ONLY if
44
Armed (N)_
Zn5 Trigger Type
45
(V+)_
46
Invert Zn5 Y/N
(N)_
Restore Zn5 Y/N
47
(Y)_
48
Delay Zn5 (secs)
(00)_
Rpt Zn5 ONLY if
49
Armed (N)_
Enable Zn6 Y/N
50
(N)_
Zn6 Trigger Type
51
(V+)_
Invert Zn6 Y/N
52
(N)_
4204/
ZONE
ENTRY
2-4204
TRIG.
2-
4204
only
2-
4204
only
2-
4204
only
2-
4204
only
4204
only
4204
only
4204
only
Section 3: Programming the GSMHS
OPTIONS
[01-15]
Defines the reporting delay in seconds for
zone 3.
[00] = no
UL: Must be set to "00."
delay
Reports alarms on zone 3 ONLY if the
[Y], [N]
conditional zone (zone 7 in zone trigger mode;
zone 4 in 4204 mode; zone 8 in 2-4204 mode) is
triggered (armed).
If [N], always reports alarms on zone 3.
4204 mode: If any zone is programmed to
"Report Only if Armed," skip to Prompt 50:
"Enable Zn6."
(EOLR)
Selects the triggering method for this zone
(V+)
input.
(V–)
Press the [space] key to scroll through choices.
[Y], [N]
Inverts the alarm and normal states of the
zone 4 trigger; otherwise uses normal input
signal.
[Y], [N]
Enables restore reporting for zone 4.
UL: Must be set to "Y."
[01-15]
Defines the reporting delay in seconds for
zone 4.
[00] = no
UL: Must be set to "00."
delay
[Y], [N]
Reports alarms on zone 4 ONLY if the
conditional zone (zone 7 in zone trigger mode;
zone 8 in 2-4204 mode) is triggered (armed).
If [N], always reports alarms on zone 4.
(EOLR)
Selects the triggering method for this zone
(V+)
input.
(V–)
Press the [space] key to scroll through choices.
[Y], [N]
Inverts the alarm and normal states of the
zone 5 trigger; otherwise uses normal input
signal.
[Y], [N]
Enables restore reporting for zone 5.
UL: Must be set to "Y."
[01-15]
Defines the reporting delay in seconds for
zone 5.
[00] = no
delay
UL: Must be set to "00."
[Y], [N]
Reports alarms on zone 5 ONLY if the
conditional zone (zone 7 in zone trigger mode;
zone 8 in 2-4204 mode) is triggered (armed).
If [N], always reports alarms on zone 5.
[Y], [N]
Enables alarm reporting for zone 6.
If [N], skip to Prompt 56: "Enable Zn7."
(EOLR)
Selects the triggering method for this zone
input.
(V+)
Press the [space] key to scroll through choices.
(V–)
[Y], [N]
Inverts the alarm and normal states of the
zone 6 trigger; otherwise uses normal input
signal.
DESCRIPTION
3-15