Page 2
Seiko Epson Corporation. The information contained herein is designed only for use with this Epson printer. Epson is not responsible for any use of this information as applied to other printers.
SpectroProofer Mounter 24"/44" User’s Guide Safety Instructions Warnings, Cautions, Safety Instructions and Notes Read all of these instructions before using your Warnings product. Also be sure to follow all warnings and must be followed carefully to avoid bodily injury. instructions marked on the product.
Auto Take-up Reel Unit. Note: The Auto Take-up Reel Unit is optional with Epson Stylus Pro 9900/9910. The SpectroProofer Mounter 24" for Epson Stylus Pro 7900/7910 does not support connecting to Auto Take-up Reel Unit.
SpectroProofer Mounter 24"/44" User’s Guide Introduction Mounter (Bottom Face) Accessories 1. Color Measurement Device carriage Moves ILS20EP/ILS20EPUV between right and 1. White calibration tile holder left. Holds the white calibration tile. 2. Mini USB interface cable 2. Backing Receives data from ILS20EP/ILS20EPUV.
SpectroProofer Mounter 24"/44" User’s Guide Introduction Color Measurement Handling Instructions Device (ILS20EP/ILS20EPUV) Color Measurement Device (ILS20EP/ILS20EPUV) ❏ Do not touch the lens directly or place the lens face down. If a scratch, dirt or other matter gets on the lens, it may affect the color measuring result.
SpectroProofer Mounter 24"/44" User’s Guide Introduction ❏ Use ILS20EP/ILS20EPUV and the white Mounter calibration tile contained in the set that comes with this product. ILS20EP/ILS20EPUV and the white Do not touch the following parts when the power calibration tile are adjusted to be a set, and is on.
User’s Guide How To Use How To Use This product is the automated color measurement system used by mounting the Epson Stylus Pro 9900/7900/9910/7910. The printer driver must be installed on the computer. To perform color measuring operation, install the SpectroProofer Utilities from the software CD-ROM, bundled with this product.
Supported Media The printer automatically prints out and measures the adjustment pattern to Some of the media supported by Epson Stylus Pro perform the setup. This process takes about 9900/7900/9910/7910 cannot be used with this one minute to complete.
SpectroProofer Mounter 24"/44" User’s Guide How To Use Measuring Color Color calibration You can perform the color calibration to keep This section introduces the color measuring high print quality with reduced color difference. procedures using SpectroProofer Utilities which is the operation tool for this product.
SpectroProofer Mounter 24"/44" User’s Guide How To Use Select the job you want to perform. Preparing and executing a color measurement job This section introduces the color measuring procedures using Preparing and executing a color measurement job. See the online help for detailed information.
SpectroProofer Mounter 24"/44" User’s Guide Maintenance Remove the white calibration tile from the Maintenance white calibration tile holder. Cleaning the Associate Parts for ILS20EP/ILS20EPUV If the color measurement value indicates abnormal value, clean the product. To maintain a Remove the backing from the printer.
See “Where To Get Help” on page 24 Attach the backing to the printer. See the instructions below to send ILS20EP/ILS20EPUV for recertification. See the SpectroProofer Mounter 24"/44" Setup Guide ❏ When sending for recertification, make sure that the white calibration tile and Set the white calibration tile to the white ILS20EP/ILS20EPUV are in the set.
Unplug the power cord from the mounter. Note: The Auto Take-up Reel Unit is optional with Epson Stylus Pro 9900/9910. The SpectroProofer Mounter 24" for Epson Stylus Pro 7900/7910 does not support connecting to Auto Take-up Reel Unit. Unplug the two interface cables connected...
When you transport the product, see the Setup Guide and be sure to repack the product using the original box and packing materials. See the SpectroProofer Mounter 24"/44" Setup Guide See the following section for removing a mounter and ILS20EP/ILS20EPUV from the printer.
SpectroProofer Mounter 24"/44" User’s Guide Troubleshooting Clean the Paper Presser using a soft, clean Troubleshooting cloth dampened with a mild detergent. Wipe it as illustrated below. Then, wipe it with a dry, soft cloth. When Error Message Appears in the Printer’s Control Panel The error message will appear on the printer’s...
Page 18
User’s Guide Troubleshooting Remove the backing from the printer. Install ILS20EP/ILS20EPUV to the mounter. See the SpectroProofer Mounter 24"/44" Setup Guide Caution: Because the backing is a fragile part, do not drop the backing while removing it. Remove any dust or dirt from the surface of the backing.
SpectroProofer Mounter 24"/44" User’s Guide Troubleshooting When SpectroProofer Utilities Ends with an Error You need to check the error message using Job status confirmation if the status of the job becomes Error completion. You can check the error messages as described below.
Confirm if there is any problem or missing dots on the print. When having a problem, confirm the status of the printer. See the User’s Guide of the Epson Stylus Pro 9900/7900/9910/7910 Canceled due to a printer error. Confirm the message on the printer’s control panel, and clear the printer error.
SpectroProofer Mounter 24"/44" User’s Guide Appendix Appendix Mac OS Quit SpectroProofer Utilities. Uninstalling Insert the Software CD-ROM to the computer. SpectroProofer Utilities Double-click the Setup icon. Follow the steps below to uninstall the SpectroProofer Utilities. Windows 2000/Windows XP Follow the on-screen instructions to uninstall the software.
78.8°F) Humidity: 35 to 65% Weight For SpectroProofer Mounter 44": Approx. 13.5 Kg (without accessories and ILS20EP/ILS20EPUV) For SpectroProofer Mounter 24": Approx. 9.0 Kg (without accessories and ILS20EP/ILS20EPUV) Dimensions For SpectroProofer Mounter 44": 1295(W) × 199(D) × 267(H) mm For SpectroProofer Mounter 24":...
Page 23
SpectroProofer Mounter 24"/44" User’s Guide Appendix Electrical Standards and approvals Rated voltage AC 100 to 240 V U.S. model: Input voltage AC 90 to 264 V Safety UL60950-1 range CAN/CSA-C22.2 No.60950-1 DC output 5.5 V 1.0 A FCC Part 15 Subpart B Class B...
New :For All products Technical Support Web Before Contacting Epson Site If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting information in your product Epson’s Technical Support Web Site provides New :Only inkjet, SPC, and Scanner products are used in this section.
In addition to your distance charges may apply. product documentation, we provide the following sources for obtaining information: Before you call Epson for support, please have the following information ready: Your Dealer ❏ Product name Don’t forget that your dealer can often help...
User’s Guide Where To Get Help Epson Helpdesk Help for Users in Thailand Epson Helpdesk is provided as a final backup to make sure our clients have access to advice. Contacts for information, support, and services New :For all products...
Epson Hong Kong Limited. Phone (62) 21-572 4350 Internet Home Page (62) 21-572 4357 Epson Hong Kong has established a local home page in both Chinese and English on the Internet Epson Service Center to provide users with the following information: Jakarta Mangga Dua Mall 3rd floor No 3A/B ❏...
❏ Information on product specifications, Information on product specifications, drivers for drivers for download download, and products enquiry are available. ❏ Frequently Asked Questions (FAQ), Sales Epson India Head Office - Enquiries, questions through e-mail Bangalore Epson Trading (M) Sdn. Bhd. Phone: 080-30515000 Head Office.
Philippines To obtain technical support as well as other after New :For All products sales services, users are welcome to contact the Epson Philippines Corporation at the telephone and fax numbers and e-mail address below: Trunk Line: (63-2) 706 2609...