Advertisement
Advertisement
Related Manuals for Epson DX5 X 1
Summary of Contents for Epson DX5 X 1
- Page 1 Epson DX5 X X X X 1 1 1 1 Printhead Printhead Epson Printhead Epson Epson DX5 Printhead Calibration Calibration Maintenance Maintenance Calibration Calibration and and Maintenance Maintenance st st st st Jan., ., ., ., 201 2013 3 3 3...
-
Page 2: Table Of Contents
Contents Contents Contents Contents Chapter 1: Computer Requirement ..............3 Chapter 2:Installation..................4 Chapter 3:Characteristic...................5 Chapter 4:Board System.................6 Chapter 5:Software Installation ..............7 Chapter 6:Software Interface................9 Chapter 7: Software Calibration..............10 Chapter 8: Other Functions and Parameters ..........14 Chapter 9: Maintenance..................15 Chapter 10: Troubleshoot................21 Chapter 11: Output Chart.................22... - Page 3 Chapter Chapter Chapter 1: 1: 1: 1: Computer Computer Computer Requirement Requirement Chapter Computer Requirement Requirement 1) 1) 1) 1) Basic Basic requirement: Basic Basic requirement: requirement: requirement: - CPU: 2.0 GHz or higher - Memory: 1Gb or higher - Hard disk: 80 Gb (recommend 20Gb free space) - Mother board: USB connection equipped - Network card - Operating system: Microsoft Windows (2000, XP)
-
Page 4: Chapter 2:Installation
Chapter Chapter 2: 2: 2: 2: Installation Installation Chapter Chapter Installation Installation 1) Move the packing box to the working site and avoid strong shaking. 2) Disassemble the wooden packing box from top to bottom. Check whether the parts are complete or not according to the packing list. - Page 5 Chapter Chapter Characteristics Characteristics � Printhead: 1pc (Epson DX5) � Resolution: 1440\1080\720DPI � Color: 4 colors � Printmode: 4,6,8,12 Pass � Output mode：File or TCP/IP(Rip and Print at the same time) � Output preview：Convert prn/prt file into a small bmp file for previewing �...
-
Page 6: Chapter 4:Board System
Chapter Chapter 4: 4: 4: 4: Board Board Board S S S S ystem ystem Chapter Chapter Board ystem ystem Printhead Printhead Printhead B B B B oard oard oard Printhead oard Magnetic sensor Status LED Encoder sensor Processing Indication Power LED Power flat... - Page 7 Note: 1. After turning on the machine till the carriage moving back to home position, the processing indication shows as: A. – 1 – 4 – 0. Main board and Head board show the same indication. 2. The two power cable plug both are 20Pin. 3.
- Page 8 3) Connet the USB data cable to the computer, and turn on the machine. PrintDrv_new PrintDrv_new file file UDT_PrintExp. UDT_PrintExp. Look for PrintDrv_new PrintDrv_new file file in the folder of UDT_PrintExp. UDT_PrintExp. It shows as above after finished installing the control software.
-
Page 9: Chapter 5:Software Installation
Chapter Chapter Chapter Chapter 6. 6. 6. 6. Software Software Software Software Interface Interface Interface Interface 1) 1) 1) 1) I I I I ntroduction: ntroduction: ntroduction: ntroduction: ouble click to open the software. Configuration Configuration definition definition Configuration Configuration definition definition：... - Page 10 Chapter Chapter Chapter Chapter 7. 7. 7. 7. Software Software Calibration Calibration Software Software Calibration Calibration 1. Nozzle checking: Print the nozzle checking to check the condition of the printhead. Make sure sure to to to to turn turn Eclosion (Feather) function before...
- Page 11 3) The second is on the right side of the first pass: Second pass First pass Adjust method: B. Turn the screw anti-clockwise: A. Loosen the 3 screws on the carriage plate: Note: Note: Every Every time time after after adjustment, adjustment, before...
- Page 12 After input the value, print the alignment again. And observe if the "0" position is the best or not. If not, repeat the above procedure until the best result come out. 4. Bi-Dir offset Bi-Dir offset is to make sure there is no bi-difference while using different speed to print. Bi-Dir offset will be set for different printing speed.
- Page 13 Have to input +2. Based on the "0" position, input the value which two line are perfectly overlapped. After input the value, test again to check the result. The step value will be different according to different media. Note: Note: Turn Turn Eclosion...
- Page 14 Chapter Chapter Chapter Chapter 8. 8. 8. 8. Other Other Other Functions Functions Parameters Parameters Other Functions Functions and and Parameters Parameters 1 1 1 1 Printhead Printhead Printhead Printhead voltage voltage voltage voltage Normally the voltage function is not being used. The range of adjusting voltage is -42V to +1.3V. 2.
- Page 15 2. 2. 2. 2. Clean Clean Clean Option: Option: Clean Option: Option: 1) Click to set the carriage go back to the flash jetting position for jetting during printing; 2) Print pass is to set every XX pass, carriage go back to the flash jetting position for jetting; 3) Clean Mode is Flash Jetting;...
-
Page 16: Chapter 9: Maintenance
Chapter Chapter Chapter Chapter 9. 9. 9. 9. Maintenance Maintenance Maintenance Maintenance 9.1 Normal Normal Normal Normal Cleaning Cleaning Cleaning Cleaning Click Clean on the main interface of the software. There are two modes of cleaning, Standard Standard Standard Standard and Depth. Depth. - Page 17 Daily Daily Maintenance Maintenance 9.4 Daily Daily Maintenance Maintenance 1. Print the nozzle checking before turn off the machine to make sure the printhead is in normal condition 2. Turn off the software, carriage go back to Home position automatically. Turn off the machine, the carriage stay at the Home position.
- Page 18 4. Take out the extend tube from the Flush, and keep it out in the air. Choose Depth clean mode to empty the Flush inside the damper and the printhead. 5. Take out the four tubes(K,C,M,Y) from the cartridge. Use the extend tube to connect them to flush.
- Page 19 Use a extend ink tube to connect the ink tube to ink pump Choose “Ink Fill” mode at control panel, use ink pump to flush ink tube until it is clear. Then take out the tube from the Flush, choose “Ink Fill” mode, empty the Flush inside the ink tube. Clean K,C,M,Y tube one by one After cleaning, use cap and fresh warp to seal the ink tubes.
- Page 20 6. Take out four cartridges, use fresh wrap to seal the ink supply hole and keep the cartridges in the proper place. Keep the carriage back to Home position and make sure the cap is perfectly sealing the printhead.
-
Page 21: Chapter 10: Troubleshoot
Chapter Chapter Troubleshoot Troubleshoot Chapter Chapter 10. 10. Troubleshoot Troubleshoot 10.1 Turn machine carriage reposition normally. Turn PrintExp then 10.1 10.1 10.1 Turn Turn Turn on on the the machine machine machine and and carriage carriage carriage reposition reposition reposition normally. normally. -
Page 22: Chapter 11: Output Chart
Chapter 11.Output 11.Output 11.Output 11.Output Chart Chart Chart Chart Output Chart Output Output Output Chart Chart Chart Printhead Epson DX5 Number of printhead Fast mode output(m Print Mode 1.6m 1.8m 2.1m 2.5m Draft 4Pass Output Standard 6Pass Quality 8Pass High Quality...