Advertisement
Quick Links
Advertisement
Related Manuals for Electrolux EQALF01TXSP
Summary of Contents for Electrolux EQALF01TXSP
- Page 1 EQALF01TXSP EQACF01TXWP USER MANUAL...
-
Page 2: Environmental Notice
This label will be used by an ELECTROLUX authorized service representative in the event that your water dispenser needs service. Environmental Notice The packaging material used is recyclable. - Page 3 Troubleshooting properties incident. power To avoid danger of suffocation, keep plastic bag away from babies and children.
- Page 4 (with cooling cabinet model not higher than 75%) This dispenser can provide hot, cold and room temperature water. The heating method of machine can only be used within 1500m elevation.
- Page 5 socket. The unit requires proper 5. Choose a place that is near a grounded electrical socket. Keep the dispenser at least 20cm away from walls and other appliances and furnitures on all 4 sides.
- Page 6 cooling On/Off. Located at the at the left side back of water dispenser.(page 6) beside until the water can flow out from the hot water spout when the hot water button be activated. 12. Unplug the unit when the unit will not be used for a long period to save electricity.
- Page 7 (for EQACF01TXWP) (for EQACF01TXWP) (for EQALF01TXSP) (for EQALF01TXSP) (for EQALF01TXSP) spout of hot water bottle supporter button of hot water drip tray button of normal water cabinet door button of cold water condenser drain hole1 cooling switch (for EQACF01TXWP only)
- Page 8 Installing the floor Bracket kit(Fig.6) 1. Use 13 mm screw to fix the fixing bracket on the side of base pan.(for EQALF01TXSP on the middle of base pan) 2. Drill out a screw hole(6 mm) on the floor. 3. Insert a screw anchor (wall plug) into the drilled hole.
- Page 9 Plug the water dispenser into the socket, the power indicator will light up, then turn on the heating/cooling switch, heating/cooling indicator will light up accordingly. (Fig.8) Slide the child safety switch to left, holding it and push hot water button vertically, then the hot water can be out.
- Page 10 Freestanding water dispenser with Cooling cabinet (For EQALF01TXSP model only) cooling switch. use the cooling cabinet. Freestanding water dispenser with cabinet (for the EQACF01TXWP model) Note: Unplug the unit before cleaning. Unplug the water dispenser from the socket.
- Page 11 Dispense water from each spout till no water flow out from spout. Place a large bucket beneath the drain hole. Remove the drain caps and allow water to drain. Once finished draining, close the drain caps.(Fig. 16) Follow the “using your water dispenser” on page 7.
- Page 12 on page 7, Make sure the water can flow out from the hot water spout when the hot water button be activated. Turn on the heating switch to heat water. 30 minutes later, drain off the liquid and clean it with water two or three times. It is recommend that this should be done every six months.
-
Page 13: Troubleshooting
Troubleshooting Water dispenser does not work • Make sure the water dispenser is properly connected to a working socket and the heating/cooling switches are set ON. Water is leaking • Unplug the water dispenser, remove bottle and replace with new one. •... - Page 14 N_COMP EARTH2 COMP COMP N_HEATER2 N_HEATER2 KEY2 EARTH KEY2 EARTH Thermostat 2 Thermostat 2 N_HEATER1 N_HEATER1 Models with cabinet Models with cooling cabinet (EQACF01TXWP) (EQALF01TXSP) EQALF01TXSP EQACF01TXWP Cooling Power 100W 120W 420W 450W 2L/h(≤10°C) R134a/36g R134a/28g L318mmxW372mmxH1005mm L310mmxW372mmxH995mm 15.5kg 13.8kg...