Table of Contents
Advertisement
Quick Links
O
WNER'S
Projection Television
43H70
55H70
61H70
TOSHIBA CORPORATION, 2000
©
M
ANUAL
TM
Owner's Record
The model number and serial number are on the back
of your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
Model number:
Serial number:
Advertisement
Table of Contents
Related Manuals for Toshiba 43H70
Summary of Contents for Toshiba 43H70
- Page 1 Owner's Record The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. Model number: Serial number:...
-
Page 2: Important Information
TV on a soft floor, make sure that the floor is not damaged by the weight of the TV. • Model 43H70 must be used only with the Toshiba stand shown on page 44. Use with other stands may result in instability and cause possible injury. -
Page 3: Table Of Contents
Introduction ... 4 Welcome to Toshiba ... 4 Exploring your new TV ... 4 Connecting your TV ... 5 Connecting a VCR ... 5 Connecting a cable converter box ... 6 Connecting a cable converter box and VCR ... 6 Connecting a DVD player or satellite receiver and a VCR ... -
Page 4: Introduction
Congratulations! You have purchased one of the finest projection TVs on the market. The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible. This manual applies to models 43H70, 55H70, and 61H70. Before you start reading, check your model number by looking at the rear of the TV. -
Page 5: Connecting Your Tv
Connecting your TV If you have not connected electronic equipment before, or you have been frustrated in the past, you may wish to read this section. (Cables are not supplied.) • A coaxial cable is the standard cable that comes in from your antenna or cable converter box. -
Page 6: Connecting A Cable Converter Box
Connecting a cable converter box This connection allows you to watch basic and premium cable channels. To use the TV’s features, select ANT-1. To view premium channels, select ANT-2, tune the TV to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels. -
Page 7: Connecting A Dvd Player Or Satellite Receiver And A Vcr
Connecting a DVD player or satellite receiver and a VCR This connection allows you to watch DVD/satellite, VCR, and TV programs, and record one TV channel while watching another channel. You will need: • one coaxial cable • two pairs of audio cables (one single and one pair of audio cables for a mono VCR) •... -
Page 8: Connecting A Dvd Player (With Or Without Colorstream™) And A Vcr
DVD and TV programs. You can record from one source while watching a program from another source. Your TV has ColorStream component video inputs. Connecting your TV to a ColorStream-compatible DVD player (such as a Toshiba ColorStream-equipped DVD player) can greatly enhance picture quality and realism. -
Page 9: Connecting A Dtv Receiver/Set-Top Box (With Or Without Colorstream™) And A Vcr
Connecting a DTV receiver/set-top box (with or without ColorStream™) and a VCR This connection allows you to watch DTV (digital TV broadcast), VCR, and TV programs, and record DTV and TV programs. You can record from one source while watching a program from another source. -
Page 10: Connecting Two Vcrs
VIDEO-3 IN AUDIO S-VIDEO VIDEO L/MONO Video-3 (front panel) of 43H70 The Video OUT jack does not output the PIP picture. The Audio OUT jacks can output the sound of either the Main or PIP picture (see “Selecting the Audio OUT sound” on page 41). -
Page 11: Connecting An Audio System
Connecting an audio system This connection allows you to use an audio amplifier to adjust the audio level. This also allows you to use external speakers. To control the audio, turn on the TV and the stereo amplifier, and turn off the built-in speakers (see“ Turning off the built-in speakers”... -
Page 12: Using The Remote Control
The remote control will operate your TV, most VCR models, and most cable TV converters together, even if they are different brands. If you will be using your TV with a Toshiba VCR, your remote control is already programmed and ready to use. If you own different brands of VCRs and/or converters, you must first program your remote control (see “Programming the remote control for use with a VCR or... -
Page 13: Programming The Remote Control For Use With A Vcr Or Cable Tv Converter
Programming the remote control for use with a VCR or cable TV converter The remote control provided with your Toshiba TV is pre- programmed to operate Toshiba VCRs. To use your TV remote control to operate non-Toshiba VCRs and cable converters: 1. -
Page 14: Cable Tv Converter Codes
Symphonic 019,344 Memorex Tatung Movie Time Teac 019,060 Technics 054,181 Teknika 019,054,056,071 Panasonic Telefunken 060,206 Paragon 227,259 Philips Toshiba 062,064,085,229, 231,385 Pioneer Totevision 056,259 Popular Mechanics 419 Unitech Pulsar Vector Vector Research 057,059 Recoton Video Concepts 059,064,080 Regal Videosonic Regency... -
Page 15: Learning About The Remote Control
Learning about the remote control back-lights the remote control buttons for five seconds LIGHT displays on-screen information (page 42) RECALL turns the TV on and off (pages 13 and 37) POWER switches between TV, cable, and VCR TV/CABLE/VCR Switch input sources (page 13) mutes the sound (page 38) MUTE selects the video input source (pages 17 and 37) -
Page 16: Setting Up Your Tv
• The menu illustrations on the following pages have been distorted for easy reference. • You can change the background of the menu. See page 42 for details. • Model 43H70 does not have the EXIT LOCKS EXIT V CH I P –... -
Page 17: Changing The On-Screen Display Language
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 43H70 DEMO MENU... -
Page 18: Adding Channels To The Tv's Memory
Adding channels to the TV’s memory Your TV will stop on specific channels that are stored in the TV’s channel memory when you press Channel y or z. Use the steps below to set all active channels in your area automatically. Programming channels automatically Your TV can automatically detect all active channels and store them in its memory. -
Page 19: Adding And Erasing Channels Manually
Convergence may drift over time or if you move the TV. If you can see clear images on the screen, skip this procedure. This adjustment should be made after the TV has been on for at least 30 minutes. 43H70 DEMO MENU TV/VIDEO VOLUME... - Page 20 To check and adjust the color convergence: 1. Press MENU, then press x or • until the PICTURE menu appears. 2. Press y or z to highlight CONVERGENCE. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 P CTURE ANTENNA MODE SPORTS...
-
Page 21: Using The Tv's Features
Using the TV’s features Adjusting the channel settings Switching between two channels You can switch between two channels without entering an actual channel number each time. To switch between two channels: 1. Select the first channel you want to view. 2. -
Page 22: Labeling Channels
To clear your favorite channels: 1. Press MENU, then press x or • until the CUSTOM menu appears. 2. Press y or z to highlight FAVORITE CH2 for example. 3. Press x or • to display the FAVORITE CH2 menu. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 CUSTOM T I MER... -
Page 23: Watching Picture-In-Picture (Pip)
6. Assign the label to the channel. Press x or • to enter a character in the first space. Press the button repeatedly until the character you want appears on the screen, then press ENTER. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 CUSTOM T I MER FAVOR I... -
Page 24: Switching The Main And Small Pictures
3. Press PIP CH y z to choose the program you want to be displayed as a small picture. If the V-CHIP feature is active and you try to watch a TV program that exceeds the rating limits you set, the TV will enter into the program block mode. -
Page 25: Freezing The Small Picture
Freezing the small picture Press STILL while you are watching a small picture. The small picture will become a still picture. To return to the moving picture, press STILL again. Using the Multi-Window feature The Multi-Window feature provides two channel search modes. One is the Preview that scans the channels programmed in the TV memory by the CH PROGRAM function (6-picture multi-search), and the other is the Favorite that scans the channels programmed in the TV... -
Page 26: Using The Strobe Function
Using the strobe function Press STROBE to start the strobe function. Nine-picture multi-strobe starts for the current main picture. For example, you can watch a decisive moment of a previously recorded sports program. To cancel the strobe function: Press STROBE again. Using the LOCKS menu The LOCKS menu includes the V-Chip, CH Lock, Video Lock, and New PIN Code functions. -
Page 27: Using The V-Chip Menu
Using the V-CHIP menu Some TV programs and movies include signals that classify the content of the program (violence, sex, dialog, language). The V-CHIP control feature in this TV detects the signals and blocks the programs according to your selections. To use this feature, perform the following setup. -
Page 28: Mpaa Rating (Independent Rating System For Movies)
MPAA RATING (Independent rating system for movies) 1. From the LOCKS menu, select MPAA RATING. 2. Press x or • to display the MPAA RATING menu, then press z or y to highlight MPAA RATING. 3. Press x or • to display the MPAA RATING menu. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 LOCKS MPAA RAT I NG... -
Page 29: Unlocking Programs Temporarily
Unlocking programs temporarily 1. If you try to watch a TV program that exceeds the rating limits you set, the TV will enter into the program lock mode. TH I S PROGRAM HAS BEEN BLOCKED ! – EXCEEDS SET L I I TS PUSH MUTE TO ENTER CABLE... -
Page 30: Locking Video Inputs
To unlock channels: 1. From the LOCKS menu, select CH LOCK. 2. Press x or • to display the CH LOCK menu. 3. Press y or z to highlight CLEAR. 4. Press x or • until “0” replaces the channel numbers you have locked. -
Page 31: Adjusting The Picture
“Save New Preference” before closing the Picture menu or the TV will change back to the previous picture quality mode when the menu is closed (see “Saving new preference” on page 32). 43H70 DEMO MENU TV/VIDEO VOLUME CHANNEL x •zy... -
Page 32: Saving New Preference
Saving new preference You can save the PICTURE items (contrast, brightness, color, tint, and sharpness) you have adjusted in the picture preference mode. To save new preference: 1. Press MENU, then press x or • until the PICTURE menu appears. 2. -
Page 33: Selecting The Color Temperature
Selecting the color temperature You can change the quality of the picture by selecting from three preset color temperatures: cool, medium, and warm. To select the color temperature: 1. Press MENU, then press x or • until the PICTURE menu appears. -
Page 34: Watching Video Input
Note: • When ColorStream HD1 or HD2 is • To receive a video OUT signal, a video or • If you select ColorStream HD1 or HD2 43H70 55H70/61H70 selected, the video OUT jack does not output a signal. S-video IN jack must be used instead of a ColorStream connection. -
Page 35: Selecting The Video Label
Selecting the video label The video label feature allows you to rename the input sources for your TV. The available video label names are as follows: –: Default label name VCR: Video Cassette Recorder DVD: DVD video player DTV: Digital TV Set Top Box SAT: Satellite box CBL:... -
Page 36: Using The Closed Caption Feature
Using the closed caption feature You have two options with the closed caption feature: captions or text. A caption is a printed version of the dialogue, narration and/or sound effects of a TV program. Text is information not related to the program that appears on half of the TV screen (if available in your area). -
Page 37: Setting The Sleep Timer
Setting the sleep timer You can set the TV so it turns off automatically. To set the sleep timer: 1. Press TIMER (or MENU and then y or z) to display the CUSTOM menu. TIMER will be highlighted. 2. After the number position starts to blink, press TIMER repeatedly to enter the length of time until the TV turns off automatically (in 10-minute increments up to 180). -
Page 38: Adjusting The Sound
2. Press y or z to highlight MTS. 3. Press x or • to highlight SAP. You will hear only the second audio program from the speakers. 43H70 55H70/61H70 Note: A second audio program (SAP) can be heard only on those TV stations that offer it. -
Page 39: Using The Feature
Using the feature feature expands the audio listening field wider and deeper to create exceptional sound quality from the TV’s speakers. The feature uses stereo signals from a TV broadcast or video input. To turn on the feature: 1. Select the stereo mode following the steps under “Selecting stereo/SAP broadcasts”... -
Page 40: Resetting Your Audio Adjustments
Resetting your audio adjustments 1. Press MENU, then press x or • until the AUDIO menu appears. 2. Press y or z to highlight RESET. 3. Press x or •. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 AUD O STEREO BASS... -
Page 41: Turning Off The Built-In Speakers
Turning off the built-in speakers Use this feature to turn the TV speakers off when you connect an audio system. (See page 11.) To turn off the built-in speakers: 1. Press MENU, then press x or • until AUDIO menu appears. 2. -
Page 42: Using The Stable Sound Feature
Using the stable sound feature The stable sound feature limits the maximum volume level to prevent extreme changes in volume when the signal source is changed (for example, an increase in volume when a TV program switches to a commercial). To turn on the stable sound feature: 1. -
Page 43: Viewing The Demonstration Mode
Viewing the demonstration mode When you press DEMO on the TV, the TV will automatically display a variety of its on-screen menus and special features. This function is provided for demonstration purposes only. To stop the demonstration mode: Press DEMO again. Understanding the auto power off feature The TV will automatically turn off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its broadcast... -
Page 44: Appendix
55H70: 195 W (average) 61H70: 195 W (average) Audio Power 14 W + 14 W Speaker Type 43H70: Two 4-3/4 inches (12 cm) round 55H70: Two 6-1/4 inches (16 cm) round 61H70: Two 6-1/4 inches (16 cm) round Video/Audio Terminals S-VIDEO INPUT Y : 1 V(p-p), 75 ohm, negative sync. -
Page 45: Troubleshooting
Troubleshooting Before calling a service technician, please check the following table for a possible cause of the problem and some solutions. Problem TV will not turn on No picture, no sound No sound, picture OK Poor sound, picture OK Poor picture, sound OK Poor reception of broadcast channels Cannot receive above channel 13 Black box appears on the screen... -
Page 46: Limited United States Warranty
ATTENTION CANADIAN CONSUMERS: Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Products purchased in the U.S.A. and used in Canada are not covered by these warranties. -
Page 47: Index
Index A/V receiver connection ... 11 ANT 1/2 ... 17 Antenna cables ... 5 Audio cables ... 5 AUDIO OUT sound, selecting ... 41 Audio system connection ... 11 Auto power off ... 43 BACKGROUND selection ... 42 Cable box connection ... 6 Cable TV converter codes ... - Page 48 HEAD OFFICE/82 TOTOWA ROAD, WAYNE, NEW JERSEY 07470 NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087 HEAD OFFICE/327 KAMAKEE STREET, HONOLULU, HI 96814, U.S.A. TEL: (808) 591-8377 HEAD OFFICE/191 McNABB STREET MARKHAM, ONTARIO L3R 8H2, CANADA TEL: (905) 470-5400 SERVICE CENTERS/TORONTO: 191 McNABB STREET MARKHAM, ONTARIO L3R 8H2, CANADA TEL: (905) 470- 5400 MONTREAL: 1643, NORTH SERVICE RD., TRANS-CANADA HIGHWAY, DORVAL QUEBEC, H9P 1J1, CANADA...