Sealey SA619 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. Operational Safety
p WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered
to when using this equipment.
p WARNING! Disconnect from air supply before changing accessories or servicing.
Maintain the drill in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will
3
invalidate the warranty.
Use in a suitable clean and tidy work area and ensure there is adequate lighting.
3
Before each use check drill bits for condition. If worn or damaged replace immediately.
3
Secure non stable work piece with a clamp, vice or other adequate holding device.
3
Ensure the chuck is securely fastened to the spindle and the drill bit is secure in the chuck.
3
Ensure there are no flammable or combustible materials near the work area.
3
p WARNING! Always wear approved eye or face and hand protection when operating the drill.
3 Use face, dust, or respiratory protection in accordance with COSHH regulations.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back
3
long hair.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the drill. Never hold a workpiece by hand.
3
Avoid unintentional starting.
3
p WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure - 90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
3
that all connections are secure.
Prolonged exposure to vibration from this drill poses a health risk. It is the owner's responsibility to correctly
3
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use the drill for a task it is not designed to perform.
7
DO NOT operate drill if any parts are damaged or missing as this may cause failure and/or personal injury.
7
p WARNING! DO NOT drill any materials containing asbestos.
DO NOT carry the drill by the hose, or yank the hose from the air supply.
7
DO NOT apply heavy pressure to the drill, let the drill do the work.
7
DO NOT place air line attachments close to your face and DO NOT point at other persons or animals.
7
DO NOT operate drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT use drill where there are flammable liquids, solids or gases such as paint solvents and including
7
waste wiping or cleaning rags etc.
DO NOT carry the drill with your finger on the trigger.
7
DO NOT direct air from the air hose at yourself or others.
7
When not in use disconnect from air supply and store in a safe, dry, childproof location.
3
2. INTRODUCTION & SPECIFICATION
Compact design is ideal for accessing working areas
where space is limited. Composite lightweight housing
reduces effects of chill on operator's hands. Fully
reversible with thumb control on side of motor housing.
Air motor with quality bearings for smooth and powerful
operation. Fitted with Jacobs keyed chuck. Suitable for
the professional workshop.
Chuck Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6mm
Free Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 1800rpm
Operating Pressure . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Consumption . . . . . . . . . . . . . . . . . . . . . . . . . 3cfm
Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4"BSP
Noise Power . . . . . . . . . . . . . . . . . . . . . . . . . . 91.5dB.A
Noise Pressure. . . . . . . . . . . . . . . . . . . . . . . . 80.9dB.A
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8kg
Original Language Version
INSTRUCTIONS FOR:
AIR DRILL 6MM
REVERSIBLE PREMIER
SA619
MODEL No:
SA619 Issue: 2 - 17/02/12