Sealey SA621.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to the instruction Wear eye protection
manual
1. SAFETY

Follow all workshop health & safety rules, regulations, and conditions when using drill.

WARNING! Disconnect from air supply before changing accessories or servicing.

Maintain the drill in good condition and replace any damaged or worn parts. Use genuine parts only. Non-authorised parts may be
dangerous and will invalidate the warranty.

WARNING! Check correct air pressure is maintained and not exceeded. We recommended 90 psi.

Keep the air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
secure.

Wear approved safety eye protection. If dust is generated wear respiratory protection. Wear protective gloves for prolonged use.

Wear suitable clothing to avoid snagging. DO NOT wear loose jewellery and tie back long hair.

Keep hands away from rotating chuck and drill bit.

Keep drill bits clean and sharp for best and safest performance.

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

Secure non stable work piece with a clamp, vice or other adequate holding device.

Ensure the chuck is securely fastened to the spindle and the drill bit is secure in the chuck.

Keep children and unauthorised persons away from the working area.

DO NOT get the drill wet or use in damp or wet locations.

DO NOT apply excessive loads to the drill bit during operation.

DO NOT hold the workpiece by hand.

DO NOT use the drill for a task it is not designed to perform.

WARNING! DO NOT use the drill if damaged or faulty. Contact your local service agent.

WARNING! Beware of high-reaction torque when breaking through the material being drilled.

DO NOT use this drill unless you have been instructed in its use by a qualified person.

DO NOT drop, throw or abuse the drill.

DO NOT carry the drill by the air hose, or yank the hose from the air supply.

DO NOT operate drill if you are tired, under the influence of alcohol, drugs or intoxicating medication.

DO NOT carry drill with your hand on the power trigger in order to avoid unintentional starting.

DO NOT direct air from the air hose at yourself or others.

When not in use disconnect from the air supply and store in a safe, dry, childproof location.

WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2. INTRODUCTION
Composite lightweight moulded housing reduces effects of chill on operator's hands. Fully reversible with thumb control set above motor
housing. Air motor with quality bearings for smooth and powerful operation. Handle exhaust with built-in muffler reduces noise level. Fitted
with Ø13mm Jacobs keyless chuck for fast bit changes. Supplied with side handle for added comfort and control. Suitable for the professional
workshop.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . SA621.V2
Chuck size:. . . . . . . . . . . . . . . . . 13mm
Free speed: . . . . . . . . . . . . . . . 800rpm
Air consumption:. . . . . . . . . . . . . . 4cfm
Operating pressure: . . . . . . . . . . . 90psi
Air inlet size: . . . . . . . . . . . . . . .1/4"BSP
Weight: . . . . . . . . . . . . . . . . . . . . . 1.4kg
Noise power: . . . . . . . . . . . . . . 91dB(A)
Noise pressure: . . . . . . . . . . . . 80dB(A)
4. CONTENTS (RIGHT)
© Jack Sealey Limited
INSTRUCTIONS FOR:
AIR DRILL 13
MM
COMPOSITE PREMIER
SA621.V2
MODEL NO:
Wear ear protection Wear protective gloves
Original Language Version
WITH KEYLESS CHUCK
SA621.V2 Issue: 2(SP) - 24/11/15