Related Manuals for Toro 31101
Summary of Contents for Toro 31101
- Page 1 Form No. 3419-919 Rev A 100in Rear Discharge Deck Groundsmaster ® 360 or 7210 Series Traction Unit Model No. 31101—Serial No. 400000000 and Up *3419-919* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Servicing the Caster Wheels and additional information, contact an Authorized Service Bearings............17 Dealer or Toro Customer Service and have the model Servicing the Blades ......... 18 and serial numbers of your product ready. The model and serial numbers are stamped into a plate that is mounted on the mower housing. -
Page 3: Safety
Safety • Wear appropriate clothing, including eye protection; substantial, slip-resistant footwear; long pants, and hearing protection. Tie back long This machine has been designed in accordance with hair and do not wear loose jewelry. EN ISO 5395:2013 and ANSI B71.4-2012. •... -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal93-6696 93-6696 1. Stored energy hazard—read the Operator's Manual. decal119-6807 119–6807 1. - Page 5 decal121-5498 121-5498 decal125-9403 125-9403 1. Height-of-cut 3. High 2. Low...
-
Page 6: Setup
314000001 and up Note: You must install Revision J or later of the Toro Diagnostic software in the vehicle controller system to operate the deck as designed. Adapter Kit, Model 31104 is for Groundsmaster® 7210 traction units in the following serial ranges:... -
Page 7: Product Overview
2. Wheel well of trailer Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor. To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. -
Page 8: Operation
Operation the 127 mm (5 inch) position there is only 1 hole, located in the second row. This does not add 6 mm (1/4 inch) to the 127 mm (5 inch) position. Note: Determine the left and right sides of the Adjust the anti-scalp rollers and skids as machine from the normal operating position. -
Page 9: Adjusting The Side Skids
Replacing the Skid Plates units. Slide the appropriate number of 13 mm (1/2 inch) spacers onto the spindle shaft to get Raise the deck wing and secure the latch pin to the desired height of cut; then slide the washer the latch handle (Figure onto the shaft. -
Page 10: Adjusting The Rollers
Cutting unit pitch is the difference in height of cut from the front of the blade plane to the back of the blade plane. Toro recommends a blade pitch of approximately 8 to 11 mm (5/16 to 7/16 inch). This means that the back of the blade plane is 8 to 11 mm (5/16 to 7/16 inch) higher than the front. -
Page 11: Operating Tips
Operating Tips Folding the Caster Arm To gain access to or from the operator area when the wing decks are folded up, release the caster arm latch (Figure 12) and rotate the caster arm away from the traction unit. g025274 Figure 12 g025273 1. - Page 12 Sharpen the blades as necessary. If a blade the load on the blades decreases. is damaged or worn, replace it immediately with a genuine Toro replacement blade. Refer to (page Alternating Mowing Direction Alternate the mowing direction to avoid making ruts in the turf over time.
-
Page 13: Maintenance
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Tighten the caster wheel nuts. After the first 2 hours • Tighten the caster wheel nuts. After the first 10 hours • Change the mower deck gearbox lubricant. After the first 50 hours •... -
Page 14: Lubrication
g025301 Figure 14 1. Pull link 4. Deck-lift chain 2. Torsion spring 5. Retainer pin 3. U-bolts 6. Shoulder screw Lubrication Service Interval: Every 50 hours The machine has grease fittings that must be lubricated regularly with No. 2 lithium grease. If the machine is operated under normal conditions, lubricate all bearings and bushings after every 50 hours of operation or immediately after every washing. - Page 15 • Wing deck hinges (10) (Figure g025837 Figure 21 g025654 Figure 18 • Folding caster arm pivot (1) (Figure g025656 Figure 19 • PTO drive shaft (2) (Figure g025658 Figure 20 • Spindle shaft bearings (5) (Figure...
-
Page 16: Servicing The Mower Deck Gearbox Lubricant
Servicing the Mower Deck Changing the Mower Deck Gearbox Lubricant Gearbox Lubricant Service Interval: After the first 50 hours The gearbox is designed to operate with SAE 80W-90 Every 400 hours gear lube. Although the gearbox is shipped with lubricant from the factory, check the level before Park the machine and cutting unit on a level operating the cutting unit for the first time. -
Page 17: Servicing The Bushings In The Caster Arms
decal121-5498 Figure 23 Belt routing Servicing the Bushings in Clean the inside of the tubes to remove any dirt. the Caster Arms Apply grease to the inside and outside of the new bushings. The caster arms have bushings pressed into the Using a hammer and a flat plate, drive the top and bottom of the tube and after many hours of bushings into the mounting tube. -
Page 18: Servicing The Blades
• Replace a worn or damaged blade. Check the blades daily for sharpness, and for any wear or damage. Sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade. - Page 19 To ensure optimum and backward (Figure 27). performance and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in non-conformance with safety standards.
- Page 20 WARNING Contact with a sharp blade can cause serious injury. Wear gloves or wrap sharp edges of the blade with a rag. Hold the blade end using a rag or a thickly-padded glove. Remove the blade bolt, the anti-scalp plate, and the blade from the spindle shaft (Figure 30).
- Page 21 Notes:...
- Page 22 Notes:...
- Page 23 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 24 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.