Table of Contents
Advertisement
Quick Links
Heated (Only) Cab Kit
2015 and After Groundsmaster
Model No. 31232—Serial No. 400400001 and Up
Safety
This product complies with all relevant European directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
1. 1) Remove the pin. 2) Raise the doors. 3) Exit the cab.
1. Close the rear window.
1. Windshield wipers—off
2. Windshield wipers
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
130-0611
130-5355
2. Raise the hood.
125-9688
3. Windshield wipers—on
4. Spray windshield washer
fluid
Register at www.Toro.com.
®
4000-D Rotary Mower
decal130-0611
1. Read the Operator's
Manual for more
information on fuses.
2. Headlight—25 A
decal130-5355
3. Condenser fan and A/C
clutch—30 A
4. Fan—25 A
decal125-9688
1. Left
Form No. 3431-618 Rev A
Operator's Manual
132-3600
5. Working light—20 A
6. Auxiliary power—15 A
7. Cab light—15 A
8. Windshield wipers—15 A
130-0457
2. Right
Original Instructions (EN)
All Rights Reserved *3431-618* A
Printed in the USA
decal132-3600
decal130-0457
Advertisement
Table of Contents
Related Manuals for Toro 31232
Summary of Contents for Toro 31232
- Page 1 Heated (Only) Cab Kit 2015 and After Groundsmaster ® 4000-D Rotary Mower Model No. 31232—Serial No. 400400001 and Up Operator's Manual Safety This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
- Page 2 decal130-5356 130-5356 1. Use the foot pedal to move forward or in reverse. decal120-0250 120–0250 1. Slow-moving vehicle decal130-0594 130-0594 1. Warning—read the Operator’s Manual; when sitting in the cab, always wear a seat belt; wear hearing protection.
- Page 3 decal121-8378 121-8378 5. External air 1. Fan—off 3. Cold air 7. Air conditioner—on (If equipped) 2. Fan—on full 4. Hot air 6. Internal air 8. Air conditioner—off (If equipped)
- Page 4 Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Apply the safety decal to the rear Safety decal window. Left foam seal Right foam seal Install the foam seals to the cab.
-
Page 5: Preparing The Machine
Preparing the Machine No Parts Required Positioning the Machine Clear a location in your workspace under the hoist system. Note: Verify that your hoist system is capable of safely supporting the cab unit over the machine during the installation. Move the machine to the workspace, lower the mower decks, shut off the engine, set the parking brake, and remove the key from the ignition switch. - Page 6 Applying the Safety Decal Parts needed for this procedure: Safety decal Procedure Note: Follow this procedure if required by local regulations. Apply the safety decal to the rear window as shown Figure g031189 Figure 2...
- Page 7 Installing the Foam Seals Parts needed for this procedure: Left foam seal Right foam seal Rear foam seal Installing the Side Foam Seals Remove the adhesive backer from the foam seals and apply them to the cab as shown in Figure Note: Apply all foam seals in this procedure 13 mm...
- Page 8 Installing the Step Plate Parts needed for this procedure: Step plate Step support Bolt (3/8 x 3-1/2 inch) Flange nut (3/8 inch) Procedure Remove the step support on the machine and then install the step support included in the cab kit as shown in Figure g034420...
- Page 9 Installing the Mower-Deck Bumper Parts needed for this procedure: Left bumper bracket Right bumper bracket Bumper Flange nut (5/16 inch) Procedure Install the bumper assembly to the left and right mower decks as shown in Figure Note: Use the existing hardware on the mower deck when you install the bumper bracket.
- Page 10 Installing the Foam Parts Parts needed for this procedure: Front seal Tread foam Rear seal Installing the Foam Parts onto the Operator Platform Install the foam parts to the operator platform (Figure g031278 Figure 6...
- Page 11 Securing the Cab to the Machine Use the existing hardware to secure the cab to the machine (Figure Installing the Cab Unit Parts needed for this procedure: Cab unit Floor tread Straight fittings Hose clamps Side-seal cover Side seal Carriage bolt (3/8 inch) Flange nut (3/8 x 3/4 inch) Connecting to the Lift Points Use the 4 lift points located on each corner of the cab...
- Page 12 Installing the Floor Tread Install the Heater-Hose Fittings Install the floor tread onto the operator platform (Figure Note: Ensure that you apply the adhesive strip to a clean surface with enough pressure to adhere the strip to the platform. g031337 Figure 10 Drain the coolant from the engine;...
- Page 13 Routing the Heater Hoses Route the heater hoses underneath the machine and into the engine compartment (Figure 12). g031424 Figure 12 Important: Do not secure the hoses to hot or moving parts. g031330 Figure 11 Note: Store the engine plugs with the ROPS assembly to use when you remove the cab.
- Page 14 Connecting the Heater Hoses Connecting the Vent Hose Connect the heater hoses to the hose fittings. Use the existing hardware to connect the vent tube from the cab (Figure 14). Note: Connect the heater hose containing the red plug to the supply port and the heater hose containing the green plug to the return port on the engine as shown in Figure...
- Page 15 Installing the Side Seal Install the side seal to the cab (Figure 15). g034423 Figure 15...
- Page 16 Installing the Tank Install washer-fluid tank to the machine (Figure 16). Installing the Washer-Fluid Tank Parts needed for this procedure: Washer-fluid tank Tank strap Tank support Carriage bolt (5/16 x 7/8 inch) Flange nut (5/16 inch) Wire harness g034424 Figure 16 Note: Use the existing hardware when you secure the tank support to the machine.
- Page 17 Routing and Connecting the Hose Connecting the Wire Harness Route the washer-fluid hose through the R-clamp Connect the wire harness for the washer-fluid bottle under the machine and toward the back of the (Figure 18). machine (Figure 17). g031444 Figure 18 g031417 Figure 17 Important:...
-
Page 18: Completing The Installation
Connecting the Wire Completing the Installation Harness No Parts Required No Parts Required Procedure Add coolant to the machine; refer to the Service Procedure Manual Locate the wire harness under the machine frame and Check for leaks. connect it to the wire harness on the cab (Figure 19). -
Page 19: Product Overview
Windshield Latch Product Overview Lift up the latches to open the windshield (Figure 21). Press the latch in to lock windshield to the open Controls position. Pull out and down on the latch to close and secure the windshield. Cab Controls g008830 Figure 21 1. -
Page 20: Recommended Maintenance Schedule(S)
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Clean the cab air filters (replace them if they are torn or excessively dirty). After the first 250 hours Cleaning the Air Filter CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. -
Page 21: Cleaning The Cab
Cleaning the Cab Storage Important: Use care around the cab seals and Remove the cab unit for storage during the warmer lights (Figure 24). If you are using a pressure months. washer, keep the washer wand at least 0.6 m (2 ft) away from the machine. - Page 22 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 23 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 24 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.