Siemens IM 328–N Description
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Control Unit
  5. IM 328-N
  6. Description
Siemens IM 328–N Description

Siemens IM 328–N Description

Sinumerik 805sm/840c link to sinec l2–dp
Hide thumbs
Table of Contents

Advertisement

Quick Links

SINUMERIK 805SM/840C
Link to SINEC L2–DP
with IM 328–N Module
Description
Manufacturer Documentation
07.96 Edition

Advertisement

Table of Contents
loading

Related Manuals for Siemens IM 328–N

Summary of Contents for Siemens IM 328–N

  • Page 1 SINUMERIK 805SM/840C Link to SINEC L2–DP with IM 328–N Module Description 07.96 Edition Manufacturer Documentation...
  • Page 2 General Hardware Configuring the Modules SINUMERIK 805SM/840C Link to SINEC L2–DP Abbreviations with IM 328–N Module Description References Manufacturer Documentation Index 07.96 Edition...
  • Page 3 6ZB5 430–0BH02–0AN0 Supplement 07.96 6ZB5 430–0BH02–1AA0 Siemens quality for software and training to DIN ISO 9001, Reg. No. 2160–01 Other functions not described in this documentation might be executable in the control. This does not, however, represent an obligation to supply such functions with a new control or when This publication was produced with Interleaf V 5.3...
  • Page 4 1. A list of abbreviations 2. A list of references 3. An index Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 5 This symbol indicates functions for which an ordering data option is required (options). The function described can only be executed if the option designa- ted is present. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 6 Programming Guide referring to operation. Note When planning, installing, starting up and operating the control, personnel concerned must be familiar with the documentation relevant to their jobs. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)

  • Page 7: Intended Use

    The device/system or system component must be used only for the applications specified in the Catalog and Reference Manual and only in conjunction with such non-Siemens devices and components as have been recommended and approved by Siemens. The product described in the manual has been developed, manufactured, tested and documented in compliance with the relevant safety standards.
  • Page 8 (e.g. by means of independent limit switches, mechanical interlocks etc.). Note The information contained in this documentation is checked and updated regularly and can be changed at any time without further notice. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 9 For information on the IM 329–N see: Reference: /7/, Description Link to SINEC L2–DP with IM 329–N Module Trademarks SIMATIC , SINEC and SINUMERIK are registered trademarks of SIEMENS AG. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)

  • Page 10: Table Of Contents

    ..............Index-1 Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0...

  • Page 11: General

    CP 5410–S5DOS/ST interface SINUMERIK 805SM SINUMERIK SINUMERIK 840C SIROTEC ACR 20 SIROTEC with module IM 329–N, master or other master stations with PROFIBUS–DP Fig. 1-1 Master stations Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 12 ET 200 ET 200 ET 200 ET 200 SINUMERIK SIROTEC IM 328–N interface module (SINEC L2–DP slave module) Fig. 1-3 Using the module IM 328-N as a slave 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)

  • Page 13: Hardware

    X111 Slave Interface X112 and LEDs have no function if Dual they exist port (DPR) X112 Fig. 2-1 Module IM 328–N with the order number: 6FC5 012–0CA03–0AA0 Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)

  • Page 14: Jumper Settings

    8 bytes S3.3 to S3.8 for an address range of 16 bytes S3.4 to S3.8 for an address range of 32 bytes 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 15 Switch S2.1 = OFF and S2.2 = ON 8–byte address range Base address S3.8 S3.7 S3.6 S3.5 S3.4 S3.3 S3.2 S3.1 1016 Significance =512 =256 =128 x: Switch position of no significance Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 16 S3.8, S3.7, S3.6, S3.5, S3.4 = ON and S3.3, S3.2 = OFF The assigned input and output area is from IB 24/QB 24 to IB 31/QB 31. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 17 (QB 0 to QB 127) Physical – – PB 0 to PB 255 interface without process image For the allocation of the I/O range for each control see: Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 18 /4/, SIROTEC ACR 20, Configuration Instructions Note The I/O range must be addressed without gaps with SIROTEC ACR 20 Reference: /5/, SINUMERIK 840C Interface Description, Part 2 – Connection Conditions 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)

  • Page 19: Elements On The Front Plate

    SINEC L2 bus connector (degree of protection IP 20, with heavy–duty thread socket) For information about the bus cable and the bus connector see: Reference: /1/, ET 200 Distributed I/O System Manual Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)

  • Page 20: Technical Data

    – 40 to + 70 C Humidity class F to DIN 40040 Shock resistance Class 12 to SN 29010 Mass 340 g Power supply + 5 V (+/– 5%), 1.1 A 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 21 (DPR) Quartz S2.1 S2.2 S4.2 Fig. 2-2 Module IM 328–N with the order number: 6FC5 012–0CA01–0AA0 Note This module has been superseded by the module 6FC5 012–0CA03–0AA0. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 22 8 bytes S3.3 to S3.8 for an address range of 16 bytes S3.4 to S3.8 for an address range of 32 bytes 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 2-10 SINUMERIK 805SM / 840C (BS)
  • Page 23 Switch S2.1 = OFF and S2.2 = ON 8–byte address range Base address S3.8 S3.7 S3.6 S3.5 S3.4 S3.3 S3.2 S3.1 1016 Significance =512 =256 =128 x: Switch position of no significance Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 2-11 SINUMERIK 805SM / 840C (BS)
  • Page 24 S3.8, S3.7, S3.6, S3.5, S3.4 = ON and S3.3, S3.2 = OFF The assigned input and output area is from IB 24/QB 24 to IB 31/QB 31. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 2-12 SINUMERIK 805SM / 840C (BS)
  • Page 25 In assigning the slaves, please note that different I/O ranges are available on the SIROTEC ACR 20, SINUMERIK 805SM and SINUMERIK 840C con- trollers (see Section 2.1.1). Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 2-13 SINUMERIK 805SM / 840C (BS)

  • Page 26: 2.2 Hardware Of The Module 6Fc5 012-0Ca01-0Aa0

    Fault on the module, system error message (see also Section 3.3.5) Interface for slave Via the interface X111 (SUB–D, socket, 9–way), the slave is connected to the SINEC L2–DP field bus. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 2-14 SINUMERIK 805SM / 840C (BS)
  • Page 27 SINEC L2 bus connector (degree of protection IP 20, with heavy–duty thread socket) For information about the bus cable and the bus connector see: Reference: /1/, ET 200 Distributed I/O System Manual Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 2-15 SINUMERIK 805SM / 840C (BS)

  • Page 28: Technical Data

    Humidity class F to DIN 40050 Shock resistance Class 12 to SN 29010 Mass 340 g Power supply + 5 V (+/– 5%), 0.28 A type 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 2-16 SINUMERIK 805SM / 840C (BS)

  • Page 29: Configuring The Modules

    How is the CP 5410 S5DOS/ST installed? How is the COM ET 200 installed on the PG? see: Reference: /1/, SIMATIC S5 Distributed I/O System ET 200 Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)

  • Page 30: Com Et 200 Parameterization Software

    In this screen form, you can press one of the following softkeys: F1: Enter the ET 200 system parameters F2: Configuration F3: Transfer functions F4: Plant documentation F5: Start–up / test F6: Diagnostics 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 31 Which inputs and outputs are assigned to which stations? To which slot and to which module type is each input and output assigned? You can also print out the current configuration status. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 32 For operation of the software and detailed information on the functions and parameters of the COM ET 200, please refer to Reference: /1/, SIMATIC S5 Distributed I/O System ET 200 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)

  • Page 33: Description Of The Dp Standard Slaves

    There is a separate configuration screen form to configure the slave interface of the IM 328–N. To make this screen form available, the appropriate type file must be installed (see Section 3.1). Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 34 16 bytes) The address IDs follow DIN E 19245 Part 3. Pressing the ENTER softkey stores the configuration data for this station in the specified program file. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)

  • Page 35: Configuration Example For Slave

    Example for IM 328–N Slave First available address: Configuration: Module address: STATION STATION DELETE ADRESS ENTER – STATION ASSIGNM. HELP EXIT STATION Fig. 3-2 CONFIGURING screen form Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)

  • Page 36: Procedure For Installation And Startup

    /7/, SIROTEC ACR20, SINUMERIK 805SM/840C Link to SINEC L2–DP with module IM 329–N – Program and activate monitoring and diagnostics functions on the master and slave sides. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)

  • Page 37: Example Of Application

    QB 16, IB 40/QB 40 and IB 64 (I 513 to I 520)/QB 64 (Q 513 to Q 520). The ET 200 system parameters have been determined for this application and entered in the program file. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 38 Units place = 5 Tens place = 0 Tens place = 0 Tens place = 0 Hundreds place = 0 Hundreds place = 0 Hundreds place = 0 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-10 SINUMERIK 805SM / 840C (BS)
  • Page 39 IM 328–N slave DP Station name: IM 328–N slave interface module SINUMERIK 840C First available address: Configuration: Module address: Fig. 3-5 Configuration of the slave in SINUMERIK 840C Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-11 SINUMERIK 805SM / 840C (BS)
  • Page 40 Station name: IM 328–N slave interface module SIROTEC ACR 20 First available address: Configuration: Module address: Fig. 3-6 Configuration of the slave in SIROTEC ACR 20 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-12 SINUMERIK 805SM / 840C (BS)
  • Page 41 QB 47 IB 95 QB 95 (I 753 (Q 753 I 760) Q 760) SINUMERIK 805SM SINUMERIK 840C SIROTEC ACR 20 Fig. 3-7 Overview of data transfer Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-13 SINUMERIK 805SM / 840C (BS)
  • Page 42 Cyclic attempt of the module to link to the SINEC L2-DP bus. Warning If no response monitoring is activated, the inputs of the station concerned are also not reset if a fault occurs but they remain unchanged. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-14 SINUMERIK 805SM / 840C (BS)
  • Page 43 Interface to the local bus of the control is disabled. When the module is accessed, the control reacts with acknowledgement delay (TO). Cyclic data transmission between master and slave is terminated. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-15...

  • Page 44: Diagnostics Functions In The S5 Program Of The Master

    Immediately after diagnostics is called in the STEP 5 program, the diagnostics data are accessed and the diagnostics message is given in the diagnostics word. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-16 SINUMERIK 805SM / 840C (BS)
  • Page 45 Station status 2 Station status 3 Master address Manufacturer ID Header Device–oriented diagnostics (station diagnostics) Header ID–oriented diagnostics (module diagnostics) Unused Unused Unused Unused Unused Unused Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-17 SINUMERIK 805SM / 840C (BS)
  • Page 46 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Without meaning Address of the master that has parameterized the slave station Fig. 3-10 Structure of the diagnostics word after request with Code = 1 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-18 SINUMERIK 805SM / 840C (BS)
  • Page 47 Always “0” device– oriented diagnostics oriented incl. “Header” diagnostics (length = 2 bytes) Fig. 3-12 Structure of the diagnostics word after request with Code = 3 Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-19 SINUMERIK 805SM / 840C (BS)
  • Page 48 T MW 252 flagword. U M 252.5 If station 5 has sent a diagnostics message, SPB FBx then evaluate error in FB x. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-20 SINUMERIK 805SM / 840C (BS)
  • Page 49 Based on the signal state of this input bit, the user can have a suitable error message displayed and can program the behaviour of the control should this fault occur. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-21 SINUMERIK 805SM / 840C (BS)

  • Page 50: Description Of The L2-Dp Slave Up To V3

    “DP standard” DP Siemens slaves, standard slaves but not FMS stations or “DP/FMS” DP Siemens slaves, standard slaves and FMS slaves. With this setting, the bus profile is set for the entire bus (timeout settings etc.). About the baud rate: Baud rates up to 1500 kBaud are possible.
  • Page 51 019 must be entered 16 times in the configuration field. Pressing the ENTER softkey stores the configuration data for this station in the specified program file. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-23 SINUMERIK 805SM / 840C (BS)
  • Page 52 Station name: SINEC L2–DP module First available address: Module address: Configuration: STATION STATION DELETE ADRESS – STATION ASSIGNM. ENTER HELP EXIT STATION Fig. 3-13 CONFIGURING screen form 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-24 SINUMERIK 805SM / 840C (BS)
  • Page 53 Add the configuration data of the new station to the existing program file Write the memory module for the IM 308–B Program and activate monitoring and diagnostics functions on the master and slave sides. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-25 SINUMERIK 805SM / 840C (BS)
  • Page 54 Based on the signal state of this input bit, the user can have a suitable error message displayed and can program the behaviour of the control in the case of this fault. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-26 SINUMERIK 805SM / 840C (BS)
  • Page 55 Interface to the local bus of the control is disabled. When the module is accessed, the control reacts with acknowledgement delay (TO). Cyclic data transmission between master and slave is terminated. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-27...
  • Page 56 ADDRESS +1 (default: I/O byte 253). Immediately after diagnostics is called in the STEP 5 program, the diagnostics data are accessed and the diagnostics message is given in the diagnostics word. 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-28 SINUMERIK 805SM / 840C (BS)
  • Page 57 L KH 0000 If no station has sent L PW 252 diagnostics message, then end of block, otherwise evaluate error JC FB xx in FB xx. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-29 SINUMERIK 805SM / 840C (BS)
  • Page 58 If diagnostics shows that the station to be checked has an error and can be PLC STOP in the addressed, the MODULE DIAGNOSTICS can be used to detect cyclic opera- slave station tion of the slave control as follows: 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-30 SINUMERIK 805SM / 840C (BS)
  • Page 59 Based on the signal state of this input bit, the user can have a suitable error message displayed and can program the behaviour of the control should this fault occur. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-31 SINUMERIK 805SM / 840C (BS)
  • Page 60 ((S. iv)) Danger This symbol means that death, serious injury or considerable material damage will occur, if the precautionary measures indicated are not taken. ((S. vi)) Technical notes Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 61 PROFIBUS–DP ((Unterschrift: )) Fig. 1–1 Master stations ((S. 2–1)) ((Bildinschriften: )) Stationsadresse für Slave = Station address for slave Einerstelle = Units place 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 62 ((Tabelle: )) Base address Significance Base address for 8–byte address range Switch S2.1 = OFF and S2.2 = ON ((Tabelle, wie oben)) x: Switch position of no significance Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 63 Interface Description, Part 2 – Connection Conditions Reference: /4/, SIROTEC ACR 20, Configuration Instructions Note The I/O range must be addressed without gaps with SIROTEC ACR 20 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 64 ((Tabelle: )) geschlossen = closed offen = open ((Block 2)) Note The IM 328–N module can only be used for SINUMERIK 805SM in the cen- tral controller. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 65 Designation SINEC L2 bus connector (degree of protection IP 20, without heavy–duty thread socket) SINEC L2 bus connector (degree of protection IP 20, with heavy–duty thread socket) 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 66 In this description, it is assumed you have the parameterization software COM ET 200 Version 4.x. 3.1.1 Installation For information about Which PG/PC can be operated on the SINEC L2–DP bus? How is the CP 5410 S5DOS/ST installed? Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 67 In this screen form, you can press one of the following softkeys: F1: Enter the ET 200 system parameters F2: Configuration F3: Transfer functions F4: Plant documentation F5: Start–up / test F6: Diagnostics ((S. 3–3)) 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 68 In the STATUS/FORCE screen form, you can see the signal condition of the inputs of all selected modules. It is also possible to force the outputs of the modules selected. ((Block 2)) Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)

  • Page 69: 3.2.1 Notes On Parameterization Of The Slaves

    There is a separate configuration screen form to configure the slave interface of the IM 328–N. To make this screen form available, the appropriate type file must be installed (see Section 3.1) ((S. 3–6)) 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-10 SINUMERIK 805SM / 840C (BS)
  • Page 70 The STEP 5 program of the IM 328–B master can request and evaluate the following diagnostics messages via the IM 328–N slave: ((Tabelle: )) ((linke Spalte: )) Diagnostics type Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-11 SINUMERIK 805SM / 840C (BS)
  • Page 71 Fig. 3–8 Request and read diagnostics Important diagnostics for IM 328–N. slave For the slave IM 328–N the following diagnostics are of considerable impor- tance: Station status Device–oriented diagnostics (station diagnostics) 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-12 SINUMERIK 805SM / 840C (BS)
  • Page 72 Load diagnostics for Code 1 (n = station number) and transfer the diagnostics word Read and evaluate the diagnostics word ((Bild)) Code = 0 Station status 1 Station status 2 ((Bild links)) Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-13 SINUMERIK 805SM / 840C (BS)
  • Page 73 The IM 328–N module (standard slave mode) and the slave interface of the IM 329–N module have the same manufacturer ID. Requesting and reading device–oriented diagnostics Code = 3 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-14 SINUMERIK 805SM / 840C (BS)
  • Page 74 Select one of the bus profiles ”DP up to V.3x” No DP standard slaves and no FMS stations (e.g. IM 328) ”DP standard” DP Siemens slaves, standard slaves but not FMS stations or ”DP/FMS” DP Siemens slaves, standard slaves and FMS slaves.

  • Page 75: Configuration Example

    L2–DP slave module (IM 328–N) into an ET 200 distributed I/O system that already exists. Assumptions: The configuration data are stored in the program file B:..6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-16 SINUMERIK 805SM / 840C (BS)

  • Page 76: Procedure For Installation And Startup

    Set and check the following data on the module in accor- dance with Sections 2.1.1 and 2.2.1: Bus interface Address range (number of input and output bytes) Module number (base address) and Address window. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-17 SINUMERIK 805SM / 840C (BS)

  • Page 77: Fault During Data Transmission

    Diagnostics: Y Diagnostics address: 252 ((Absatz darunter von alter S. 6–3 übernehmen)) ((Rest der neuen S. 3–28 von alter S. 6–3, ohne Änderungen, übernehmen)) ((S. 3–29)) 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-18 SINUMERIK 805SM / 840C (BS)
  • Page 78 If an additional slave station with SINEC L2–DP slave module is switched on while the system is running, PLC STOP is output in the slave station while the control is being power up. Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-19...
  • Page 79 ET 200U Distributed I/O device, modular design to degree of protection IP 20, for uni- versal applications especially in intelligent modules Function block Fieldbus Message Specification 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-20 SINUMERIK 805SM / 840C (BS)
  • Page 80 Bus system SINEC L2 with DP protocol (stands for distributed peripherals) Softkey Serial Periphery Controller SRAM Static RAM (buffered) Station number Each ET 200 bus node is assigned a unique station number Software Version x Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 3-21 SINUMERIK 805SM / 840C (BS)
  • Page 81 Order No.: 6ZB5 430 – 0BH02 – 0AA0 SIROTEC ACR 20, SINUMERIK 805SM/840C Link to SINEC L2–DP with Module IM 329–N Description Order No.: 6ZB5 430 – 0BH02 – 0AA1 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved 3-22 SINUMERIK 805SM / 840C (BS)

  • Page 82: A Abbreviations

    Distributed I/O device, compact design to degree of protection IP 65, for use in an industrial environment ET 200U Distributed I/O device, modular design to degree of protection IP 20, for uni- versal applications especially in intelligent modules Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)
  • Page 83 PROFIBUS–DP Standard proposal PROFIBUS–DP (DIN E 19245, Part 3) on which the distri- buted I/O system ET 200 is based I/O word Peripheral byte Random Access Memory 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved SINUMERIK 805SM / 840C (BS)
  • Page 84 Standard plug–in station (1 SPS = 15–24 mm) SRAM Static RAM (buffered) Station number Each ET 200 bus node is assigned a unique station number Software Version x Timeout Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)

  • Page 85: B References

    Order No.: 6ZB5 430 – 0BH02 – 0AA0 SIROTEC ACR 20, SINUMERIK 805SM/840C Link to SINEC l2–DP with Module IM329–N Description Order No.: 6ZB5 430–0BH02–0AA1 x: Edition number Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 SINUMERIK 805SM / 840C (BS)

  • Page 86: Index

    Module 6FC5 012–0CA01–0AA0, 2-16 Module 6FC5 012–0CA01–0AA0, 2-9 Module 6FC5 012–0CA03–0AA0, 2-8 Module 6FC5 012–0CA03–0AA0, 2-1 Type file, 3-2 Jumper settings Module 6FC5 012–0CA01–0AA0, 2-10 Module 6FC5 012–0CA03–0AA0, 2-2 Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0 Index-1 SINUMERIK 805SM / 840C (BS)

This manual is also suitable for:

Im 329–n

Table of Contents