Assembly And Adjustment - DeWalt D28113 Manual

E N G L I S H
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
2
Conductor size (mm ) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15
Voltage Amperes Cable rating (Amperes)
115 0 - 2.0 6
2.1 - 3.4 6
3.5 - 5.0 6
5.1 - 7.0 10 10
7.1 - 12.0 15 15
12.1 - 20.0 20 20
230 0 - 2.0 6
2.1 - 3.4 6
3.5 - 5.0 6
5.1 - 7.0 10 10
7.1 - 12.0 15 15
12.1 - 20.0 20 20

Assembly and adjustment

WARNING: Prior to assembly and
adjustment always unplug the tool.
MOUNTING AND REMOVING THE GUARD (FIG. B1 & B2)
D28111/D28139 - GUARD WITH FIXING SCREW (FIG. B1)
• Place the angle grinder on a table, spindle up.
• Align the lugs (5) with the notches (6).
• Press the guard down and rotate it to the
required position.
• Securely tighten the screw (7).
• To remove the guard, slacken the screw.
WARNING: Never use the tool without
the guard in place.
D28113(K)/D28130/D28132C/D28134/D28135(K)/D28141 -
KEYLESS GUARD (FIG. B2)
• Place the angle grinder on a table, spindle up.
• Release the clamping lock (8) and hold the guard
(3) over the tool as shown.
30
FITTING AND REMOVING A GRINDING OR CUTTING DISC
25 30 45 60
(FIG. C1 & C2)
6 6 6 6 10
6 6 6 15 15
6 10 15 20 20
15 20 20 25
20 25 25 -
25 - - -
6 6 6 6 6
6 6 6 6 6
6 6 6 10 15
10 10 15 15
15 15 20 20
20 20 25 -
MOUNTING THE SIDE HANDLE (FIG. D)
Instructions for use
• Align the lugs (5) with the notches (6).
• Press the guard down and rotate it to the
required position.
• If required, increase the clamping force by
tightening the screw (9).
• Tighten the clamping lock.
• To remove the guard, release the clamping lock.
WARNING: Never use the tool without
the guard in place.
• Place the tool on a table, guard up.
• Fit the inner fl ange (10) correctly onto the spindle
(11) (fi g. C1).
• Place the disc (12) on the fl ange (10). When
fi tting a disc with a raised center, make sure that
the raised centre (13) is facing the fl ange (10).
• Screw the outer fl ange (14) onto the spindle (11)
(fi g. C2):
– the ring on the fl ange (14) must face towards
the disc when fi tting a grinding disc (A);
– the ring on the fl ange (14) must face away from
the disc when fi tting a cutting disc (B).
• Press the spindle lock (2) and rotate the spindle
(11) until it locks in position.
• Tighten the fl ange (14) with the two-pin spanner
supplied.
• Release the spindle lock.
• To remove the disc, loosen the fl ange (14) with
the two-pin spanner.
WARNING: Do not use a damaged disc.
• Screw the side handle (4) tightly into one of the
holes (14) on either side of the gear case.
WARNING:
• Always observe the safety instructions
and applicable regulations.
• Ensure all materials to be ground or cut
are secured in place.