Advertisement
5. OperatIOn
▲
cautIOn: If the filler cap is opened too quickly, without taking the necessary precautions, there is a very high risk of injury. The metal
parts can be extremely hot; avoid contact with the skin. Risk of burns.
NOTE: The filler cap will not unscrew if the tank is pressurised.
5.1.
FIllInG
WarnInG! Before filling/refilling turn off and remove from mains supply. Always allow to cool for 10 minutes before adding water.
‰
5.1.1.
Ensure there is no more steam by unlocking the steam trigger in the ON position.
5.1.2.
Remove the filler cap by turning counter clockwise.
5.1.3.
Fill the water tank using the funnel and measuring cup provided. The maximum capacity of the tank is 2L. Tip: DO nOt overfill the
tank.
5.1.4.
Replace the filler cap by turning clockwise until a good seal is achieved.
5.2.
hanDle OperatIOn
lOckeD OFF pOsItIOn
hanDle (1)
5.3.
releasInG steam
trIGGer lOck
(un-lOckeD)
5.4.
aFter use
Lock the steam trigger in the OFF position (A) to prevent accidental operation.
5.5.
OperatIOn refer to contents section above
5.5.1.
Make sure the Steamer is unplugged and the switch in the OFF position.
Unscrew the tank filler cap by turning counter clockwise.
5.5.2.
5.5.3.
Using the measuring cup and the funnel, fill the Steamer with 1.8L of water. (This will produce about 35 minutes of steam.)
Replace the filler cap by screwing it clockwise.
5.5.4.
5.5.5.
Attach the extension tubes to the steam handle to use the steam mop or attach chosen accessory.
5.5.6.
Connect the appliance to the mains supply and press the switch to the ON position.
5.5.7.
Two lights come on. The indicator light comes on to indicate that the power is turned on. The orange steam light comes on to
indicate a rise in steam pressure in the appliance.
5.5.8.
The appliance is ready for use when the orange steam indicator light goes out and the pressure reaches between 4 and 5 bar
depending on the water level in the tank (red zone of the steam pressure gauge).
5.5.9.
During use, the orange steam indicator light may turn on again. This indicates that the steam pressure may not be high enough.
In this case, release the steam trigger for a few moments. When the orange steam indicator light goes off again, can resume
using steam.
5.5.10.
If the pressure drops below 2 bar, the steam flow may not be sufficient depending on the accessory used. In this case, release
the steam trigger and wait until the steam pressure gauge reaches the red zone again.
5.5.11.
When activating the steam trigger, water may appear. This is quite normal because at the beginning, the steam takes a little time to
arrive and the water condenses in the hose and the extension tubes.
5.5.12.
After a few moments the water will turn into steam.
5.5.13.
When activating the steam trigger, a lot of water can flow. This may be due to a residue of steam from the previous use that has
turned into water. Empty this water by operating the steam trigger over a bucket or sink. Once this water has passed, you can use
your device normally again.
5.5.14.
When using the accessories, the surface you are cleaning may be wet. This is due to the steam that turns into water in contact
with this surface. Use a sponge or cloth to wipe this surface.
© Jack Sealey Limited
The steam trigger (2) is located in the handle and the steam trigger
lock latch is located under the handle (3). The lock has two positions:
OFF / LOCK and ON / UNLOCK. Press the front of the steam trigger
lock latch to lock the steam (A) and press the back to unlock (B) the
Steam.
steam
trIGGer (2)
trIGGer
lOck (3)
(lOckeD)
When the pressure gauge (6) reaches the red zone, refer to picture
above, the Steamer is ready for use (maximum pressure of 5 bar).
Press the steam trigger lock latch (A) to the ON position (B) and
press the steam trigger (C) to obtain a steam jet. Release the
trigger to stop the jet of steam.
Original Language Version
VMSC01 | Issue:1 04/12/19
Advertisement
