Husqvarna AUTOMOWER 535 AWD Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Lawn Mower
  5. Automower 535 AWD
  6. Operator's manual

Husqvarna AUTOMOWER 535 AWD Operator's Manual

Robotic lawn mowers
Hide thumbs Also See for AUTOMOWER 535 AWD:
Table of Contents

Advertisement

Quick Links

Operator's manual
®
HUSQVARNA AUTOMOWER
535 AWD
EN, English
Read the operator's manual carefully and make sure that you
understand the instructions before you use the product.

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna AUTOMOWER 535 AWD

Summary of Contents for Husqvarna AUTOMOWER 535 AWD

  • Page 1 Operator's manual ® HUSQVARNA AUTOMOWER 535 AWD EN, English Read the operator's manual carefully and make sure that you understand the instructions before you use the product.

  • Page 2: Table Of Contents

    Contents 1 Introduction 6 Troubleshooting 1.1 Support............3 6.1 Introduction - troubleshooting....41 1.2 Product description........3 6.2 Fault messages........41 ® 1.3 Automower Connect.........3 6.3 Information messages......48 1.4 Product overview ........4 6.4 Indicator lamp in the charging station..49 1.5 Symbols on the product......5 6.5 Symptoms..........

  • Page 3: Introduction

    Serial number: PIN code: The serial number is on the product rating plate and on the product carton. • Use the serial number to register your product on www.husqvarna.com. 1.1 Support The operator selects the operation settings in ® Automower Connect app.

  • Page 4: Product Overview

    1.4 Product overview Ultrasonic sensors Charging plates Front top cover On/Off-button Lifting handle LED status indicator Rear top cover STOP button 4 - Introduction 1427 - 002 - 20.12.2019...

  • Page 5: Symbols On The Product

    START button WARNING: Read the 10. Front wheels user instructions before operating the product. 11. Rear wheels 12. Battery cover 13. Rear chassis box with electronics, motors WARNING: Disable the and battery product before working on 14. LED for operation check of the charging or lifting the product.

  • Page 6: Symbols On The Battery

    The chassis contains components Do not discard the battery into fire and which are sensitive to electrostatic do not expose the battery to a heat discharge (ESD). The chassis must source. also be resealed in a professional manner. For these reasons the chassis shall only be opened by authorized service technicians.
  • Page 7 1.7.1 Menu structure overview 1 Schedule Overview Schedule settings Edit Change current Add new Schedule settings Schedule settings Cutting height Cutting height Operation ECO mode Weather timer Cutting time Medium High 1427 - 002 - 20.12.2019 Introduction - 7...
  • Page 8 1.7.2 Menu structure overview 2 Installation Drive Starting Lawn coverage Find past wire point charging station Charging Follow Follow guide station signal boundary wire 1/2/3 How often Area GPS assisted 1/2/3/4/5 navigation (default) Accessories Mower house 8 - Introduction 1427 - 002 - 20.12.2019...
  • Page 9 1.7.3 Menu structure overview 3 General Time & date Reset to factory settings Mower time Mower date Time & date Reset to factory settings (Edit) (Edit) from phone Security Change PIN code Theft protection GeoFence New loop signal Create new loop signal Carried Alarm...
  • Page 10 1.7.4 LED status indicator LED indication Status Green In operation Blue Parked Error Yellow Paused/stopped Flashing yellow PIN code needed Pulsating green/blue Charging in progress Flashing green/blue Push the ON/OFF button to confirm start of opera- tion Flashing green, low- Inactive frequent White...

  • Page 11: Safety

    2 Safety 2.1 IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE The operator is responsible for accidents or hazards occurring to other people or property. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities (that could affect a safe handling of the product), or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person...

  • Page 12: Safety Definitions

    or the adjacent area if the instructions WARNING: The product in the manual are not obeyed. can be dangerous if used incorrectly. Note: Used to give more information that is necessary in a given situation. WARNING: Do not use 2.3 Safety instructions for operation the product when 2.3.1 Use persons, especially...
  • Page 13 Refer to off the product on page 33 . page 27 . • Husqvarna does not guarantee full compatibility between the product and other types of wireless systems such as remote controls, radio transmitters, hearing loops, underground electric animal fencing or similar.
  • Page 14 2.3.3 How to lift and move the product WARNING: The product must be switched off before you lift it. The product is switched off when the LED status indicator is not lit. CAUTION: Do not lift the product when it is parked in the charging station. It can damage the charging station and/or the product.
  • Page 15 2.3.5 In the event of a thunderstorm To reduce the risk of damage to electrical components in the product and the charging station, we recommend that all connections to the charging station are disconnected (power supply, boundary wire and guide wire) if there is a risk of a thunderstorm.

  • Page 16: Installation

    • Make a mark on the blueprint where to put the charging station, the boundary wire and the guide wire. Note: Refer to www.husqvarna.com for more • Make a mark on the blueprint where the information about installation. guide wire connects to the boundary wire.
  • Page 17 interference with the signal from the charging station. max. 5 cm / 2" max. 5 cm / 2" • Put the power supply in an area with a roof and protection from the sun and rain. • Put the power supply in an area with good airflow.
  • Page 18 " > 5 cm / 2 " 35 cm /14 • Put the boundary wire 30 cm / 12 in. (C) from an obstacle that is 1-5 cm / 0.4-2 in. high. Note: Make a blueprint of the work area before you install the boundary wire and guide wire.
  • Page 19 • Make an eyelet (F) where the guide wire is Note: If a passage is less than 2 m / 6.5 ft. wide, to be connected to the boundary wire. install a guide wire through the passage. 3.4.3.1 To put the boundary wire in a slope The product can operate in 70% slopes.
  • Page 20 CAUTION: Do not put the guide wire across the boundary wire, for example a boundary wire that goes to an island. 1.5 m/5 ft 1.5 m/5 ft 0 cm/0" 3.4.3.4 To make a secondary area Make a secondary area (B) if the work area has 2 areas that are not connected with a passage.

  • Page 21: Installation Of The Product

    3.4.4 To examine where to put the guide 3.4.5 Work area examples wire • If the charging station is put in a small area (A), make sure that the distance to the Put the guide wire from the charging station boundary wire is at a minimum 3 m / 10 ft.
  • Page 22 WARNING: The product is only to be Put the charging station in the selected area. used with the power supply unit supplied by Husqvarna. Note: Do not attach the screws for the charging station to the ground until the guide To install the guide wire is installed.
  • Page 23 To install guide wire is complete. Refer to 3.5.4 To install the guide wire the boundary wire on page 23 and To CAUTION: Twinned cables, or a screw install the guide wire on page 23 . terminal block that is insulated with Attach the charging station to the ground insulation tape are not satisfactory with the supplied screws after the guide wire...

  • Page 24: To Put The Wire Into Position With Stakes

    3.7 To bury the boundary wire or the Note: Make sure that you can see the guide wire end of the guide wires through the transparent area of the coupler. • Cut a groove in the ground with an edge cutter or a straight shovel.

  • Page 25: After The Installation Of The Product

    3.9 After the installation of the product Sign up for a Husqvarna account in the ® Automower Connect app. 3.9.1 To do a visual check of the charging Log in to your Husqvarna account in the station ® Automower Connect app.

  • Page 26: To Start The Product For The First Time

    PARK START MORE DETAILS Schedule Schedule Schedule Schedule 3.11 To start the product for the first Log on to your Husqvarna account in the ® Automower Connect app to pair your time ® product with Automower Connect. When the product is switched on for the first time,...

  • Page 27: Settings In Automower ® Connect

    Select product. Divide the m / yd of the lawn with the approximate operation capacity. Refer to ® Obey the instructions in the Automower table below. Connect app. The result is equal to the number of hours ® 3.12 Settings in Automower Connect that the product must operate each day.
  • Page 28 3.12.3.1 To find the charging station Weather timer is reset if the product Note: The The product can be set to search for the charging does not operate for more than 50 hours, or if a Reset of all user settings is done. The Weather station in 3 methods: timer is not changed if a Reset of schedule Charging station signal...
  • Page 29 distance from the charging station on page Move the horizontal bar to set the time delay. 29 . Save . Select Move the horizontal bar to set how often the product goes to each area. At all other 3.12.3.2 Lawn coverage times, the products starts to cut near the The product has GPS Assisted Navigation that charging station.
  • Page 30 on/off to enable or disable the product moves back into the work area. The Select factory setting for the Drive Past Wire function function. function is 31 cm. You can select a distance of Save . Select 20-50 cm. ® 3.12.5 General (Bluetooth only) Note: With the factory setting the product will cut...
  • Page 31 To create a New loop signal product is more than 500 m / 1650 ft away from the center position the product will be deactivated Put the product in the charging station. and an alarm will start. The PIN code is needed Settings >...

  • Page 32: Operation

    4 Operation 4.1 To switch on the product WARNING: Read and understand the safety chapter before you switch on the product. WARNING: Keep your hands and feet away from the rotating blades. Do not put your hands or feet near or below the product when the motor is running.

  • Page 33: To Stop The Product

    4.2.3.2 Park for a selected number of hours Note: If the LED status indicator is lit or is The product goes to the charging station where it flashing in any color the product is not stays for a selected number of hours, then it LED status indicator switched off.
  • Page 34 Note: During the first weeks after a new installation, the cutting height must be set to MAX to avoid damaging the loop wire. After this, the cutting height can be lowered step by step every week until the desired cutting height has been reached.

  • Page 35: Maintenance

    WARNING: The product must be a soft brush to clean the product. switched off before any maintenance is Husqvarna recommends to use a special done. The product is disabled when cleaning and maintenance kit, available as the LED status indicator is not lit.

  • Page 36: Replace The Blades

    Rotate the skid plate so that its holes align with the screws for the blade. WARNING: Use blades and screws of the right type. Husqvarna can only guarantee safety when using original blades. Only replacing the blades and reusing the screw can result in a screw wearing during mowing.

  • Page 37: To Replace The Top Covers

    Check that the blades can pivot freely. 5.4 To replace the top covers The top cover is an accessory available in different colors. Speak to your local Husqvarna representative for more information. CAUTION: Clean grass and dirt from the product before you remove the covers.
  • Page 38 Put a protection between the cover and the link arm. This is to prevent damage to the top cover. Pull up the top cover. Push the front top cover into position. 5.4.3 To remove the rear top cover Remove the top cover. To switch off Switch off the product.

  • Page 39: Battery

    5.6 Winter service WARNING: Only charge the product using a charging station and power Take your product to your Husqvarna central supply which is intended for it. service for service prior to winter storage. Incorrect use may result in electric...
  • Page 40 • Testing of the product’s function and components. • Checking and, if required, replacing wear items such as blades and bearings. • Testing the product’s battery capacity as well as a recommendation to replace battery if necessary. • If new firmware is available, the product is updated.

  • Page 41: Troubleshooting

    There is a proposal as to the cause and steps to take for each message. This chapter also presents some symptoms that can guide you if the product does not work as expected. More suggestions for steps to take in the event of malfunction or symptoms can be found on www.husqvarna.com. 6.2 Fault messages ®...
  • Page 42 Contact your local Husqvarna representative if the same message appears often. For more information, refer to Messages on page 31 . Message Cause Action No loop signal The power supply or the voltage cable Examine the LED status on the charg- are not connected.
  • Page 43 PIN code to your registered time. e-mail address. If you have not regis- tered the e-mail address, contact your local Husqvarna representative. Empty battery The product cannot find the charging Change the position of the guide wire.
  • Page 44 Message Cause Action Charging station The contact between the charging Put the product in the charging station blocked strips and contact strips may be poor and check that the charging strips and and the product has made a number of contact strips make good contact.
  • Page 45 Message Cause Action Electronic problem Temporary electronic or firmware rela- Restart the product. ted issue. Loop sensor prob- If the problem remains, the message requires action by authorized service technician. Charging system problem Tilt sensor prob- Temporary prob- STOP button prob- Ultrasonic problem GPS navigation problem...
  • Page 46 Message Cause Action Connectivity prob- ® Problem with the Automower Connect Restart the product. module. If the problem remains, the message requires action by authorized service technician. Outside work area The boundary wire connections to the Make sure that the boundary wire is To exam- charging station are crossed.
  • Page 47 Message Cause Action Weak GPS signal The sky is obstructed in large parts of If possible, remove obstructing objects. the work area. Disable the GPS navigation function and use the lawn coverage function in- Lawn coverage on page stead. Refer to 29 .

  • Page 48: Information Messages

    6.3 Information messages ® The table below shows a number of information messages that may be shown in Automower Connect. Contact your local Husqvarna representative if the same message appears often. For more Messages on page 31 . information, refer to...

  • Page 49: Indicator Lamp In The Charging Station

    For a fully functional installation, the indicator lamp in the charging station must emit a solid or flashing green light. If something else appears, follow the troubleshooting guide below. There is more help on www.husqvarna.com. If you still need help, please contact your local Husqvarna representative.

  • Page 50: Symptoms

    If your product does not work as expected, follow the symptoms guide below. There is a FAQ (Frequently Asked Questions) on www.husqvarna.com which provides more detailed answers to a number of standard questions. Contact your local Husqvarna representative if you still cannot find the reason for the fault.

  • Page 51: Find Breaks In The Loop Wire

    Symptoms Cause Action The product is The STOP button has been activated. Make sure that the START button is parked for hours in pushed down. the charging sta- Parking mode is activated. Select the operating mode in Automow- tion. ® Connect.
  • Page 52 Indicator lamp in the boundary loop. Refer to in the charging station on page 49 . Check that the boundary wire connections to the charging station are properly connected and not damaged. Check that the indicator lamp in the charging station is still flashing blue.
  • Page 53 Continue until only a very short section of the wire remains which is the difference between a solid green light and a flashing blue light. Then follow instruction in step 5 below. If indicator lamp still flashes blue in step 3 above: Put AL and G1 back in their original positions.

  • Page 54: Transportation, Storage And Disposal

    Note: If you keep the charging station outdoors, do not disconnect the power supply and the connectors. • Contact Husqvarna sales representative about what accessories are available for your product. 7.3 Disposal Remove the two screws and remove the •...
  • Page 55 Disconnect the two cables from the battery and remove the battery. 1427 - 002 - 20.12.2019 Transportation, storage and disposal - 55...

  • Page 56: Technical Data

    8 Technical data 8.1 Technical data ® Dimensions Automower 535 AWD AWD Length, cm / in. 93 / 36.6 Width, cm / in. 55 / 21.6 Height, cm / in. 29 / 11.4 Weight, kg / lbs 17.3 / 38.1 ®...
  • Page 57 ® Mowing Automower 535 AWD AWD Cutting system 3 pivoted cutting blades Maximum blade motor speed, rpm 2475 Power consumption during cutting, W +/- 20 % Cutting height, cm / in. 3-7 / 1.2-2.8 Cutting width, cm / in. 22 / 8.7 Narrowest possible passage, cm / in.

  • Page 58: Registered Trademarks

    Connect 4G Power Class 3 23 dBm Husqvarna AB does not guarantee full compatibility between the product and other types of wireless systems such as remote controls, radio transmitters, hearing loops, underground electric animal fencing or similar. The products are made in England or the Czech Republic. See information on the rating plate. Refer to Introduction on page 3 .

  • Page 59: Warranty

    The blades and wheels are seen as disposable and are not covered by the warranty. If an error occurs with your Husqvarna product, please contact Husqvarna customer service for further instructions. Please have the receipt and the product’s serial number at hand when contacting Husqvarna customer service.

  • Page 60: Applicable To Us/Ca Market

    10 Applicable to US/CA market 10.1 Supplier's Declaration of Note: Changes or modifications made to this Conformity equipment not expressly approved by Husqvarna may void the FCC authorization to operate this Issuer: Husqvarna AB, Drottninggatan 2, S-561 equipment. 82 Huskvarna, Sweden www.husqvarnagroup.com.
  • Page 61 1427 - 002 - 20.12.2019 Applicable to US/CA market -...
  • Page 62 62 - Applicable to US/CA market 1427 - 002 - 20.12.2019...
  • Page 63 1427 - 002 - 20.12.2019 Applicable to US/CA market -...
  • Page 64 ® AUTOMOWER is a trademark owned by Husqvarna AB. © Copyright 2019 HUSQVARNA. All rights reserved. www.husqvarna.com Original instructions 1141840-95 2019-12-20...

Table of Contents