Summary of Contents for Husqvarna AUTOMOWER 535 AWD
Page 1
Operator's manual ® HUSQVARNA AUTOMOWER 535 AWD EN, English Read the operator's manual carefully and make sure that you understand the instructions before you use the product.
• If there is a risk of thunderstorm, Husqvarna or mental capabilities or lack of experience and recommends that the power supply and all the knowledge, if they have been given supervision...
27 . Husqvarna recommends to set the • The product must only be operated, maintained and repaired by persons that are fully conversant product to operate when the work area has no with its special characteristics and safety activity.
1.7 To lift and move the product WARNING: The product must be set to OFF before you lift it. The product is OFF when the LED status indicator goes off. CAUTION: Do not lift the product when it is parked in the charging station. It can cause damage to the charging station and/or the product.
The serial number and the product number are on the product rating plate and on the product carton. • Register your product on www.husqvarna.com. Enter the serial number of the product, the product number and the date of purchase to register your product.
15. Rear chassis box with electronics, motors and WARNING: Keep a safe dis- battery tance from the product when 16. LED for operation check of the charging station operating. Keep your hands and boundary wire and feet away from the rotat- ing blades.
2.7 Symbols on the battery Status WARNING: Lithium-ion batteries can Green In operation explode or cause fire if disassembled, Blue Parked short-circuited or handled roughly. Do not expose to water, fire or high temperature. Error Yellow Paused/stopped Flashes yellow PIN code is necessary Read the user instructions.
The sound level decreases after some time. Note: Refer to www.husqvarna.com for more 3.4 Before the installation of the wires information about installation. You can select to attach the wires with stakes or bury 3.2 Main components for installation...
Page 11
• If the charging station is installed on an island, The boundary wire should be put as a loop around the make sure to connect the guide wire to the island. work area. Sensors in the product senses when the To make an island on page 13 .
Page 12
3.4.4 To examine how to put the boundary wire around the charging station • Husqvarna recommends to put the boundary wires straight out from the charging station (A). " > 5 cm / 2 " 35 cm /14 • Put the boundary wire 30 cm / 12 in. (C) from an obstacle that is 1-5 cm / 0.4-2 in.
Page 13
> 1.5 m / 5 ft > 1.5 m / 5 ft >60 cm / 24" >30 cm / 12" > 1.5 m / 5 ft 0% - 50% 50% - 70% • Make sure that there is an area of cm / ft. between level ground and steep slopes.
Page 14
To make an island, isolate areas in the work area with the boundary wire. We recommend to isolate all stable objects in the work area. Note: The product must be manually moved between Some obstacles are resistant to a collision, for example, the main area and the secondary area.
• If the work area has a slope, put the guide wire in a straight line from the bottom of the slope to the top of the slope. If it is not possible to make a straight line, put the guide wire diagonally across the slope. CAUTION: Do not put the guide wire in parallel with the slope, as the...
Page 16
When connecting the power supply, only use a power outlet that is connected to an residual-current (RCD) device. Read and understand the instructions about the To examine where to put charging station. Refer to the charging station on page 10 . Put the charging station in the selected area.
Cut the boundary wire with a pair of wire cutters. CAUTION: Cutting the grass too low 10. Connect the guide wires to the boundary wire with right after installation can damage the wire a coupler. insulation. Damage to the insulation may not cause disruptions until several weeks or months later.
Automower Connect is a free app for your mobile mobile device. device. Use the app for installation, settings and Sign up for a Husqvarna account in the operation of your product. You can also find more ® Automower Connect app.
3 minutes, set the product to OFF and then set the product to ON. Enter the factory PIN code. Log on to your Husqvarna account in the ® Automower Connect app.
Page 20
My mowers in the Automower ® Select Connect app, and add your product. ® Follow the instructions in the Automower Connect app. 20 - Installation 1427 - 009 - 20.12.2022...
4 Settings The product has factory settings but the settings can be Quality Operation frequency adapted to each work area. Pro sport quality Each day 4.1 Schedule Pro quality Each second day Regular quality Each third day 4.1.1 To calculate the schedule setting Schedule you can change the schedule settings for Calculate the dimension of your lawn in m / yd...
, avg or max . ECO mode disables the signal in the boundary wire, Note: Husqvarna recommends to set the charging guide wire and the charging station, when the product is max . It is usually better to move the station signal to parked or is charging.
Page 23
4.4.2 To do a test of the boundary wire Area C, approximately 20% Installation > Find charging station > Test: Select Boundary wire setup. Put the product 3 m / 9 ft. from the boundary wire, facing the boundary wire. Push the START button.
Connect app. Make a note of the new PIN code in Memo. Refer to Introduction on page 6 . Note: Husqvarna recommends to use the headlights at night time. 4.7.3 Theft protection Theft protection menu it is possible to set the In the 4.5.2 To avoid collisions with the...
™ Download the Husqvarna Fleet Services app and ® Automower Connect app to your mobile device. Log on to the Husqvarna Fleet Services ™ app. Follow the instructions about how to pair the ™ product with Husqvarna Fleet Services 1427 - 009 - 20.12.2022...
5 Operation 5.1 To set the product to ON The product can only go from the charging station when the battery is full and if the Schedule is set to let the product to operate. WARNING: Read and understand the safety chapter before you use the product.
Push the ON/OFF button for 3 seconds. Make sure that the LED indicator goes off. Note: If the LED indicator is on or if it flashes. Refer to LED status indicator on page 9 . Note: The product cannot be set to OFF when it is in the charging station.
6 Maintenance 6.1 Introduction - maintenance It is important that the blade disc rotates easily and that the edges of the blades are not damaged. The usual lifetime of the blades are 3 to 6 weeks. The conditions WARNING: Set the product to OFF that follow can increase or decrease the lifetime of the before you do maintenance on the product.
The product does not operate satisfactorily in slopes if the wheels are blocked with grass. Use a soft brush to clean the product. Husqvarna recommends to use a special cleaning and maintenance kit, available as accessory. Speak to your Husqvarna representative for more information.
6.4 Replacement of the blades WARNING: Husqvarna can only guarantee safety if you use Husqvarna original blades with the embossed crowned H-mark logotype. WARNING: You must replace the screws when you replace the blades. The used screws can wear quickly and make the blade come loose, this can cause serious Make sure that the blade disc can rotate freely.
6.5 To replace the top covers The top cover is an accessory available in different 6.5.2 To install the front top cover colors. Speak to your local Husqvarna representative for more information. Put the front top cover on the snap-on clips.
Page 32
Put a protection between the cover and the link arm to prevent damage to the top cover. Lift the top cover. Push the front top cover into position. Remove the top cover. 6.5.3 To remove the rear top cover To set the product Set the product to OFF.
6.7 Winter service Speak to your Husqvarna central service to make winter service before storage of the product. Do winter service of the product yearly to keep the product in good condition. The winter service usually includes the procedures that follow: •...
Automower Connect and some the message needs to be confirmed on the product. Contact Messages on your local Husqvarna representative if the same message appears often. For more information, refer to page 25 . Message...
Page 35
PIN code to your registered e-mail address. If you have not registered the e-mail address, contact your local Husqvarna representative. Empty battery The product cannot find the charging station. Change the position of the guide wire. Refer To install the guide wire on page 16 .
Page 36
Message Cause Action Lifted A blockage has activated the lift senors and Remove the product from the blockage. If the caused the product to stop. problem remains it requires action by author- ized service technician. Lifted in link arm A blockage has activated the lift sensor in the Remove the product from the blockage.
Page 37
Message Cause Action Battery temperature The product does not operate if the battery The product starts to operate again when the outside limits temperature is too high or too low. temperature is between the set limits and the schedule settings let the product to operate. Make sure that the charging station is put in an area with protection from the sun.
Page 38
Message Cause Action Limited cutting height The cutting height adjustment cannot move. Examine the cutting height adjustment and remove grass and other unwanted materi- Unexpected cutting al. If the problem remains, the message re- height quires action by authorized service techni- cian.
Page 39
Message Cause Action No loop signal The power supply or the voltage cable are Examine the LED status on the charging sta- not connected. tion. If the LED is not lit, it indicates that there is no power. Examine the power outlet con- nection and whether an earth-fault breaker has tripped.
® The table below shows a number of information messages that may be shown in Automower Connect. Contact your Messages on page local Husqvarna representative if the same message appears often. For more information, refer to 25 . Message Cause...
If your product does not work as expected, follow the symptoms guide below. There is a FAQ (Frequently Asked Questions) on www.husqvarna.com which provides more detailed answers to a number of standard questions. Contact your local Husqvarna representative if you still cannot find the reason for the fault.
Page 42
Symptoms Cause Action The battery is empty If the battery has been deeply discharged, Keep the product in the charging station for and you put the prod- it will take a long time to charge the battery 24 hours and test if the product can be set uct in the charging and before the product can be set to ON.
Symptoms Cause Action ® The product only The product does not have cellular connec- Enter the Automower Connect app on your ® ® ® has Bluetooth (short tion to the Automower Connect app. mobile device. Select Automower Connect range) connection and do a new pairing operation.
Page 44
other end of this new loop wire at the middle of the suspected wire section. POWER Switch the connections between the guide wire and the boundary wire in the charging station. Start by switching connection AL and G1. Some models have additional guide wires (G2, G3). The same procedure can be followed for them.
Page 45
Continue until only a very short section of the wire remains which is the difference between a solid green light and a flashing blue light. Then follow instruction in step 5 below. If indicator lamp still flashes blue in step 3 above: Put AL and G1 back in their original positions.
Note: If you keep the charging station outdoors, do not disconnect the power supply and the connectors. • Speak to your Husqvarna service for information about available storage accessories for your product. 8.3 Disposal • Obey the local recycling requirements and applicable regulations.
Page 47
Disconnect the 2 cables from the battery and remove the battery. 1427 - 009 - 20.12.2022 Transportation, storage and disposal - 47...
9 Technical data 9.1 Technical data ® Dimensions Automower 535 AWD Length, cm / in. 93 / 36.6 Width, cm / in. 55 / 21.6 Height, cm / in. 29 / 11.4 Weight, kg / lbs 17.6 / 39 ® Electrical system Automower 535 AWD...
Page 49
® Sound data Automower 535 AWD Sound level perceived, dB (A) Measured sound power noise level, dB (A) Noise emissions uncertainties KWA, dB (A) Sound pressure noise level at the operator’s ear , dB (A) ® Mowing Automower 535 AWD Cutting system 5 pivoted cutting blades Maximum cutting motor speed, rpm...
Deviations from this general technical data are included in the country specific chapters. Husqvarna AB does not guarantee full compatibility between the product and other types of wireless systems such as remote controls, radio transmitters, hearing loops, underground electric animal fencing or similar.
The blades and wheels are seen as disposable and are not covered by the warranty. If an error occurs with your Husqvarna product, please contact Husqvarna customer service for further instructions. Please have the receipt and the product’s serial number at hand when contacting Husqvarna customer service.
12 Translated EU Declaration of Conformity We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN, Tel. +46 36 146500 declare on our sole responsibility that the product: Description Robotic lawn mower Brand Husqvarna Type/Model HUSQVARNA AUTOMOWER ® 535 AWD Identification Serial numbers dating from 2023 week 2...