Battery Type; Package Contents; Assembly And Adjustments - DeWalt DCR017 Manual

EnglIsh
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care for the
environment.
Charge D WALT battery packs only with designated
e
D WALT chargers. Charging battery packs other
e
than the designated D
D WALT charger may make them burst or lead to
e
other dangerous situations.
Do not incinerate the battery pack.

Battery Type

The DCR017 operates on 10.8 volt, 14.4 volt and 18 volt XR
Li-Ion battery packs.
These battery packs may be used: DCB141, DCB142, DCB143,
DCB144, DCB145, DCB181, DCB182, DCB183, DCB183B,
DCB184, DCB184B, DCB185. Refer to Technical Data for
more information.

Package Contents

The package contains:
1 Charger/Radio
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Charger/Radio
The following pictograms are shown on the charger/radio:
Read instruction manual.
Description (Fig. A–C)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Power button
1
Volume dial
2
Arrow buttons
3
Mode button
4
Menu button
5
Memory buttons
6
Enter/Display button
7
LCD display
8
Battery compartment latch
9
Battery receptacle
10
Auxiliary port
11
Coin cell battery door
12
22
WALT batteries with a
e
Coin cell battery
13
Outlets
14
Charging light
15
USB power output port
16

ASSEMBLY AND ADJUSTMENTS


WARNING: Use only D
e
Inserting a Battery Pack (Fig. A, C)
nOtE: Make sure your battery pack is fully charged. If the
battery pack does not produce sufficient power, charge the
battery pack following the instructions in the manual of the
charger.
nOtE: To ensure maximum performance and life of Li-Ion
batteries, charge the battery for a minimum of 10 hours before
first use.
1. Release the latch to open the battery compartment
9
cover.
2. Insert the battery pack 19
fully seated.
3. Close and latch the battery compartment cover.
Fuel Gauge Battery Packs (Fig. C)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button
20 . A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOtE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
To Install the Coin Cell Battery (Fig. A, B)

WARNING: When replacing battery, replace it with the
same brand and type. Observe correct polarity (+ and –)
when replacing batteries. Do not store or carry batteries so
that metal objects can contact exposed battery terminals.
Your radio is equipped with memory capacity in order to store
the time and your selected memory channels. When the radio is
OFF, this memory capacity is powered by one coin cell battery
that is included with the radio.
1. Turn the charger/radio off and unplug from the power
source.
2. Open the battery compartment by lifting the battery
compartment latch 9 .
3. Unscrew the screw on the battery door
18
4. Press down on the battery door latch and pull to open.
5. Install the coin cell battery
inside the coin cell battery area.
6. Replace the battery door, insert screw and tighten.
7. Securely close the battery compartment.
WALT battery packs and chargers.
into the receptacle 10 until it is
.
12
13 according to the diagram