Sealey bg200/99.V3 Instructions

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
ear instructions protection protection
1. Safety
1.1. electrical Safety
 Warning! it is the user's responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
maintained in a safe condition and routinely PAt (Portable Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.

ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.

regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.

Ensure that the
used and
 dO nOt pull or carry the appliance by the power cable. 
by the cable.

dO nOt use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired
or replaced immediately by a

13
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
a) Connect the GREEN/YELLOW earth
b) Connect the BROWN live
c) Connect the BLUE
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
qualified electrician.
1.2. general Safety

Warning! disconnect the grinder from the mains power, and ensure the grinding wheels are at a
attempting to change
safety
wire brush on appropriate models.

maintain the grinder in good condition and check moving parts alignment regularly.

replace or repair damaged parts. use recommended parts only. non authorised parts may be dangerous and will invalidate the
warranty.
▲
danger! dO nOt use a damaged stone as it is dangerous and may cause damage or serious personal injury.

Warning! Only persons qualified under
current grinding wheel
mains power and

Warning! Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts.
any other part that is damaged should be repaired or replaced before tool is used. the safety guard is a mandatory fitting
© Jack sealey limited
bench grinder Ø200mm 600W/230V heaVy-duty
Wear a mask
voltage rating on
that the plug
fuse rating in these instructions.
qualified electrician.
This product is
Amp 3 pin
Ensure that repairs
qualified electrician.
contact
wire
wire to
neutral wire to
Sealey recommend
accessories, service or perform any maintenance.
note: With
instructions
the
certificate are to change
refer to chapter
Original Language Version
instructions for
model no:
Wear
if used in the course of business duties, it must be
the appliance suits
is fitted with
dO nOt pull the plug from the socket
fitted with a
plug.
are carried out
Replace a
with a BS1363/A
3 pin plug. If
a qualified electrician.
to the earth
terminal 'L'.
the live
terminal 'N'.
the neutral
that repairs are
the exception of
will also apply
"Abrasive Wheels Regulations"
or dress grinding stones.
"Grinding Stones" for
4
bg200/99.V3
the power supply
the correct fuse
BS1363/A
by a
damaged plug
13 Amp
in doubt
terminal 'E'.
carried out by
standstill before
"Abrasive Wheels Regulations"'
to use of
and holding
Unplug grinder
details.
all
to be
- see
recommended fuse rating
5 Amp
a
a
a
from
A guard or