CIP5000 series storage Table of contents | en Table of contents Safety RoHS compliance About this guide Introduction System overview Front panel Rear panel 3.2.1 Rear panel components Secure cover 3.3.1 Install the cover Setup tasks Task 1: unpacking Task 2: install enclosure on the rack Task 3: install disk drives 4.3.1...
| Safety CIP5000 series storage Safety Warning! This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Danger! Consequences The electronic components within the enclosure are sensitive to damage from Electro-Static Discharge (ESD).
This document gives a brief overview of the CIP5000 series storage, and then provides instructions to install the system hardware in the rack, and configure necessary network and I/ O device connections. For more details on installation and operation of the CIP5000 series storage, refer to the User manual. Introduction...
| System overview CIP5000 series storage System overview This section gives an overview of the front panel, rear panel and secure cover of CIP5000 series storage. Front panel The front panel hardware components on the CIP-5316W-00N and CIP-5424W-00N are identical except the number of drives.
CIP5000 series storage System overview | en Figure 3.3: CIP-5316W-00N rear view Figure 3.4: CIP-5424W-00N rear view 3.2.1 Rear panel components The rear panel components of CIP-5316W-00N and CIP-5424W-00N are the same, and each model has two power supply units (PSU). PSU fan vents...
| System overview CIP5000 series storage VGA port DVI port HDMI port USB 3.0 (4 ports) Optical SPDIF Out port Audio In/Out ports 1000BASE-T RJ-45 (2 ports) Secure cover The CIP5000 enclosure include a secure cover for better physical security and to prevent unintended or accidental removal of hard drives.
CIP5000 series storage System overview | en 3.3.1 Install the cover Figure 3.7: Installing or removing secure cover To attach the secure cover: Make sure the lock is in the unlocked position. To unlock, insert the key into the lock and turn counter clockwise.
| Setup tasks CIP5000 series storage Setup tasks Finish the basic setup tasks described in the guide. Task 1: unpacking Note that the two models are nearly identical, except for the number of disk drive bays. Packing List The box contains the following items: –...
Page 11
Additional loading on the rails is at the customer’s risk. Caution! Bosch cannot guarantee that the mounting rails will support your CIP enclosure hardware unless you install them as instructed. Install the enclosure to the rack using the optional rails.
Page 12
| Setup tasks CIP5000 series storage Rail ends attach on the outside of the front and rear rack posts Figure 4.2: Rail ends attach to the outside of each post Brackets 3U 16-bay enclosure hardware Rails installed and tightened Figure 4.3: Placing the enclosure hardware onto the rack rails...
CIP5000 series storage Setup tasks | en Vertical rack post Handles mount Mounting rails mount outside the rack post outside the rack post Figure 4.5: System installed in rack To install the enclosure hardware into a rack with the supplied rails: Check the fit of the rails in your rack system.
| Setup tasks CIP5000 series storage Figure 4.7: Drive slot numbering for 4U models Slot numbering is mapped in the web-based system Management GUI. Insert all of the drive carriers into the enclosure to ensure proper airflow, even if you do not populate all the carriers with disk drives.
CIP5000 series storage Setup tasks | en 4.3.3 Install 3.5" disk drive in the carrier Obey the following instructions to install 3.5” hard disk drives into the drive carriers. Remove a disk drive carrier. Carefully lay the disk drive into the drive carrier at the front, so that the screw holes on the sides line up correctly with the power and data connectors facing away from the carrier handle.
| Setup tasks CIP5000 series storage Figure 4.10: I/O ports on the rear panel Connections for system management on rear panel: VGA port 1000BASE-T RJ-45 ports USB 3.0 ports 4.4.1 Initial setup Use a USB or PS/2 keyboard and a VGA monitor to establish a direction connection to the Windows operating system.
CIP5000 series storage Setup tasks | en Notice! The enclosure is equipped with LED indicators on the power supply units. Check the LEDs after powering the devices on to make sure the cooling and power status for the power module is normal.
| Setup tasks CIP5000 series storage 4.5.2 Front panel LED behavior The table below describes LED behavior when boot-up is finished and the system is operating normally: Description Power Blue - System is powered on. System status Green - System is normal.
CIP5000 series storage Setup tasks | en PSU 1 PSU 2 Description PSU 1 or PSU 2 Green - normal operation Red or Orange - a problem or unit failure 4.5.5 Rear panel LED behavior When system boot-up is finished, use the LEDs on the controller on the rear of the device to monitor various functions.
| Setup tasks CIP5000 series storage 4.7.1 Log into management GUI Double click the Management GUI link icon (WebPAM PROe) on the desktop to launch the default browser and go to the login page. When the log-in screen appears: –...
Page 21
CIP5000 series storage Setup tasks | en Log into the Management GUI. If there are no arrays configured, you will be automatically directed to the Disk Array Configuration menu. The Disk Array Configuration menu offers three options for configuration. Select one of the options: –...
Page 22
| Setup tasks CIP5000 series storage Check the boxes to select any one or a combination of: – Redundancy - The array remains available if a physical drive fails – Capacity - The largest possible amount of data capacity –...
Page 23
Uncheck the box if you want to disable Media Patrol. Enable Drive Health Polling. Enable Power Management – Bosch recommends leaving these features enabled. Physical Drives – Highlight physical drives you need from the Available list and press the >> button to move them to the Selected list.
| Setup tasks CIP5000 series storage – This value is the data capacity of the first logical drive in your new disk array. If you specify less than maximum capacity, the remaining capacity is available for additional logical drives which you can create now or later.
CIP5000 series storage Technical support | en Technical support For technical support, please provides the following information: – Product model and serial number – BIOS, firmware and driver version numbers – A description of the problem or situation – System configuration information, including: motherboard and CPU type, hard drive models, SAS/SATA/ATA/ATAPI drives &...
| Disposal CIP5000 series storage Disposal Electrical and electronic waste This product and/or battery must be discarded separately from household waste. Discard this product according to local laws and regulations, to allow its reuse and/or recycling. This will help in conserving resources, and in protecting human health and the environment.
Page 27
CIP5000 series storage Disposal | Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028...
Page 28
| Disposal CIP5000 series storage 2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.