Sealey PWH615 Manual

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. sAfety
WArning! This helmet is not suitable for use with laser welding or CUTTInG or for overhead welding applications.
‰
ensure all workshop safety rules, regulations and conditions are complied with when using welding equipment. The helmet will not
9
offer protection against misuse of workshop tools, equipment, or accessories.
Maintain the helmet in good condition and protect cartridge from liquid and dirt contact. Regularly replace the protective lens and
9
replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
ensure the front cover window is securely in place before use.
9
Fit the helmet and adjust the head band so the helmet will sit as low and near to your face as possible.
9
Use helmet only in temperatures ranging from -5°C to 55°C.
9
Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery.
9
Maintain correct balance and footing.
9
Ensure the floor is clear from obstructions, not slippery and wear non-slip protective shoes.
9
Keep children and unauthorised persons away from the working area.
9
WArning! The helmet will only protect the eyes and face from radiation and sparks. It will not protect against explosive devices or
‰
corrosive liquids.
do not use helmet for any purpose for which it is not designed.
8
do not use helmet unless you have been instructed in its use by a qualified person.
8
do not open or tamper with the shade cartridge.
8
do not get the helmet wet or use in damp or wet locations.
8
do not leave work place with helmet in lowered position, as bright light source may darken cartridge unexpectedly.
8
do not place the helmet on a hot surface.
8
do not use helmet without front cover window fitted. To do so will invalidate your warranty.
8
Clean helmet (see section 5.5) and store the helmet in a safe, dry, childproof location.
9
WArning! Before welding always inspect the cartridge filter to ensure that it is not damaged. To test the filter prior to welding,direct
‰
the front of the cartridge filter to a bright light source which will cause the lens to darken. Then using your hand rapidly cover and
uncover the sensor. The filter should lighten momentarily then return to a dark state.
WArning! do not use the helmet if damaged or you suspect it may be faulty. (Contact Sealey Stockist).
‰
▲ dAnger! do not use if, at any time, the face plate in the cartridge FAIlS to darken when exposed to a welding spark. Remove
cartridge and return to your Sealey stockist for checking.
Continued use of the product knowing that the auto darkening feature is noT FUnCTIonInG may dAMAGe YoUR eYeS and
9
CAUSe BlIndneSS.
▲ dAnger! do not wear this respirator system to enter areas where:
1. Atmospheres are oxygen deficient.
2. Contaminant concentrations are unknown.
3. Contaminant concentrations are Immediately dangerous to life or Health.
4. Contaminant concentrations exceed the maximum use concentration determined using the assigned Protection Factor for the
specific respirator system.
WArning! The Particle filter can not be cleaned. do not attempt to remove contamination using for example compressed air as
‰
this will destroy the filters, the equipment will not give the expected protection and the warranty will be invalidated.
If ventilation is poor, wear an approved air-supplied respirator.
9
Read and understand the Material Safety data Sheets and the manufacturer's instructions for metals, consumables, coatings,
9
cleaners, and degreasers.
Work in confined space only if it is well ventilated, or while wearing an air-supplied respirator. Always have a trained watch-
9
person nearby. Welding fumes and gases can displace air and lower the oxygen level causing injury or death. Be sure the breathing
air is safe.
do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapours to
8
form highly toxic and irritating gases.
do not weld on coated metals, such as galvanized, lead, or cadmium plated steel, unless the coating is removed from the weld
8
area, the area is well ventilated, and while wearing an air-supplied respirator. The coatings and any metals containing these
elements can give off toxic fumes if welded. ReSPIRAToR (PAPR) MISUSe can be hazardous. Welding produces fumes and gases.
Breathing these fumes and gases can be hazardous to your health.
Read and follow these instructions and the safety labels carefully. The powered air purifying respirator (PAPR) helps protect the
9
© Jack Sealey limited
Welding Helmet WitH Air Purifying
resPirAtor Auto dArkening sHAde 5-8 & 9-13
PWH615
Model no:
Original Language Version PWH615 Issue 1 15/08/19