Sealey PWH617 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Charger indoor
instructions use only
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with
all electrical products. If the product is used in the course of business duties, it must be maintained in a safe condition and routinely
PAT (Portable Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used.
DO NOT pull or carry the appliance by the cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Class II products are wired with live (brown) and neutral (blue) only and are marked with the Class II symbol;
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GENERAL SAFETY
Ensure all workshop safety rules, regulations and conditions are complied with when using this equipment. The face shield will
9
not offer protection against misuse of workshop tools, equipment, or accessories.
Maintain the welding helmet in good condition and protect cartridge from liquid and dirt contact.
9
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Fit the face shield and adjust the head band so the face shield will sit as low and near to your face as possible.
9
Ensure that the face hood is securely attached to the face shield.
9
Use welding helmet only in temperatures ranging from -5°C to 55°C.
9
Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery.
9
Maintain correct balance and footing.
9
Ensure the floor is clear from obstructions, not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
Use of this welding helmet is for face and eye protection against low energy impact and splashing liquids.
9
Inspect the welding helmet frequently as a pitted or scratched face shield reduces vision and therefore should be replaced
9
immediately.
Be aware if wearing standard ophthalmic spectacles they may transmit impacts, creating a hazard for the user.
9
Before welding, adjust the auto-darkening lens sensitivity setting to meet the application.
9
Stop welding immediately if the auto-darkening lens does not darken when the arc is struck.
9
DO NOT use if any part of the welding helmet is cracked or broken.
8
DO NOT place this product on a hot surface.
8
DO NOT use this face shield for protection against gases, ultra violet or infra red radiation, ionising radiation, liquids under
8
pressure or other severe hazards.
DO NOT use this face shield against heavy impact hazards, the lens is breakable.
8
DO NOT use welding helmet for any purpose for which it is not designed.
8
WARNING! DO NOT use the welding helmet if damaged or you suspect it may be faulty. (Contact Sealey Stockist).
‰
DANGER! DO NOT wear this respirator system to enter areas where:
▲
1. Atmospheres are oxygen deficient.
2. Contaminant concentrations are unknown.
3. Contaminant concentrations are Immediately Dangerous to Life or Health.
4. Contaminant concentrations exceed the maximum use concentration determined using the assigned Protection Factor for the
specific respirator system.
If ventilation is poor, wear an approved air-supplied respirator.
9
Work in confined space only if it is well ventilated, or while wearing an air-supplied respirator. Always have a trained watch-
9
person nearby. Ensure the breathing air is safe.
© Jack Sealey Limited
AUTO DARKENING WELDING HELMET WITH
TH2 POWERED AIR PURIFYING RESPIRATOR
(PAPR)
PWH617
MODEL NO:
Original Language Version PWH617 Issue 1 06/01/23