Advertisement
Quick Links
Road Light and Homologation Kit
Workman
Model No. 133-7128
This product contains a chemical or chemicals known to the State of California to
Note: The Brake and Signal Kit (Toro Part No. 132-8579 for the Workman GTX or 133-7127 for the Workman GTX
Electric) must be installed on the machine to install this kit.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
GTX Series Utility Vehicle
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
Headlight
Headlight adapter
Cable tie
Wire harness
Plate light
Phillips-head screw (#10 x 5/8 inch)
Locknut (#10)
Plate bracket
Push fastener
Serial plate
Speed plate
Plate-mount bracket
Pop rivet (3/16 x 0.92 inch)
No parts required
Register at www.Toro.com.
WARNING
CALIFORNIA
Qty.
–
2
2
5
1
2
4
4
1
2
1
3
2
17
–
Form No. 3407-216 Rev A
Installation Instructions
Use
Prepare the machine.
Install the headlights.
Install the plate bracket and wire
harness.
Install the serial plate.
Install the speed plates.
Complete the installation.
Original Instructions (EN)
All Rights Reserved *3407-216* A
Printed in the USA
Advertisement
Related Manuals for Toro 133-7128
Summary of Contents for Toro 133-7128
- Page 1 This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Note: The Brake and Signal Kit (Toro Part No. 132-8579 for the Workman GTX or 133-7127 for the Workman GTX Electric) must be installed on the machine to install this kit.
-
Page 2: Preparing The Machine
Preparing the Machine No Parts Required Procedure 1. Move the machine to a level surface (box A of Figure 2. Engage the parking brake (box B of Figure 3. Remove the key from the ignition switch (box C of Figure 4. - Page 3 Installing the Plate Bracket and Wire Harness Parts needed for this procedure: Wire harness Plate light Phillips-head screw (#10 x 5/8 inch) Locknut (#10) Plate bracket Push fastener Installing the Push Fasteners g035942 Figure 3 1. Beneath the cargo bed, measure 267 mm (10-1/2 inches) rearward from the edge of the frame cross tube 1.
- Page 4 3. Drill 2 holes (6.35 mm or 1/4 inch diameter) in the plastic cargo bed (Figure 4. Install the 2 push fasteners into the holes. Installing the Plate Bracket and Wire Harness 1. Remove the 4 existing flange-head bolts from the underside of the cargo bed and use them to install the plate bracket (Figure...
- Page 5 5. Install the plate lights to the plate bracket using the 4 Phillips-head screws (#10 x 5/8 inch) and 4 locknuts (#10) as shown in Figure 6. Unplug the left taillight wire harness from the Brake and Signal Kit wire harness. 7.
- Page 6 Installing the Speed Plates Parts needed for this procedure: Speed plate Plate-mount bracket Pop rivet (3/16 x 0.92 inch) Installing the Speed Plates to the Seat Base Sides 1. On the left side of the machine, measure 51 mm (2 inches) from bottom, left of the seat base side, and mark this location (Figure...
- Page 7 Installing the Speed Plate to the Tailgate 7. Install the plate-mount bracket to the seat base side using 4 pop rivets (3/16 x 0.92 inch) as shown in 1. On the right side of the tailgate, measure 95 mm (3.75 Figure inches) from the right edge of the tailgate and 70 mm (2.75 inches) from the top of the tailgate, and mark...
-
Page 8: Completing The Installation
Completing the Installation No Parts Required Procedure Install the negative battery cable to the battery.