Toro BC-25 Operator's Manual page 5

•
Ensure that the area is clear of other people before
operating the machine. Stop the machine if anyone enters
the area.
•
Never leave a running machine unattended. Always stop
the engine and verify the chipper flywheel has stopped
rotating.
•
Do not touch parts which may be hot from operation.
Allow them to cool before attempting to maintain, adjust,
or service the machine.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
•
Do not allow anyone to operate this machine without
proper instruction.
•
Keep area of discharge clear of people, animals, buildings,
glass, or anything else that will obstruct clear discharge,
cause injury, or damage. Wind can also change discharge
direction. If it becomes necessary to push material into
the hopper, use a small diameter wood stick, not your
hands.
•
Do not use the machine with the hopper or discharge
chute removed.
•
Clear the area of objects such as wire, rope, etc. Inserting
these objects into the hopper could damage the flywheel
and/or cause injury.
•
Keep your face and body away from the hopper to avoid
accidental bounce back of any material.
•
If you hear or see material being kicked back against the
rubber flap, shut the feeder chute door until the material
has passed.
•
When feeding material into the hopper, be extremely
careful that pieces of metal, rocks, or other foreign
objects are not included. Personal injury or damage to
the machine could result.
•
Shut off the engine and wait for the moving parts to come
to a complete stop before removing processed material,
leaves, or debris from the machine.
•
Remove the key, disconnect the spark plug wires and keep
the wire away from the spark plug to prevent accidental
starting while adjusting the machine.
•
If the cutting mechanism strikes a foreign object or if
your machine should start making an unusual noise or
vibration, stop the engine and wait five minutes for all
moving parts to come to a complete stop and cool.
Vibration is generally a warning of trouble. Disconnect
the spark plug wires and inspect for clogging or damage.
Clean and repair and/or replace damaged parts.
•
Do not touch parts that may be hot from operation.
Allow them to cool before attempting to maintain, adjust,
or service the machine.
•
Never move this machine while the engine is running.
•
Before every use:
– Inspect the coupler, ball and hitch.
– Ensure that all lights are functioning properly.
– Ensure that the tires are properly inflated as
recommended.
– Ensure that the lug nuts are tight and torqued
properly.
– Ensure that the machine is properly secured.
Maintenance and Storage
•
Stop the engine. Wait for all movement to stop before
adjusting, cleaning, or repairing.
•
Clean debris from the mufflers and engine to help prevent
fires. Clean up any oil or fuel spillage.
•
Let the engine cool before storing.
•
Do not store fuel near flames or drain indoors.
•
Park the machine on level ground. Never allow untrained
personnel to service the machine.
•
Remove the spark plug wire before making any repairs.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Keep all parts in good working condition and all hardware
tightened. Replace all worn or damaged decals.
•
Keep all nuts, bolts, screws, hydraulic fittings, and hose
clamps securely tightened. Keep equipment in good
condition.
•
Do not tamper with safety devices.
•
Use extra care when handling gasoline and other fuels.
They are flammable and vapors are explosive.
– Use only an approved container.
– Never remove the gas cap or add fuel when the
engine is running. Allow the engine to cool before
refueling. Do not smoke.
– Never refuel the machine indoors.
– Never store the machine or fuel container inside
where there is an open flame, such as near a water
heater or furnace.
– Never fill a container while it is inside a vehicle, trunk,
pick-up bed, or any surface other than the ground.
– Keep container nozzle in contact with the tank during
filling.
•
Stop and inspect the machine if you strike an object.
Make any necessary repairs before restarting.
•
Use only genuine Toro replacement parts to ensure that
the original standards are maintained.
5