Download Print this page
Logitech Alert 750n Getting Started
Logitech Alert 750n Getting Started

Logitech Alert 750n Getting Started

Master system
Hide thumbs Also See for Alert 750n:

Advertisement

Quick Links

Getting started with
Logitech
Alert~
?SOn
(o'~
Logitech·
CD
Lega
l Warning
Certain uses o
f
security
camera products and audio
devices. such as employee
monitoring. surreptitious
viewing and record ing of
images and/or audio, or the
use. publication o
r
dist
ribu
-
tion of image and/or audio
record ings. a re prohibited or
restricted by country.
st
ate
and local laws
1 Logitech Alert Camera
2 Software install CD
5 Mounting accessories
9 Suct ion cup
Be sure to comply with the
laws in your count ry. state.
and locality when using
Log1tech Alert products and
6 Camera power supply
10 Cable extender
3 Power supply cable (yellow
t
ips)
7 Network adapter
11 System Requirements Guide
Master System
PC
4 Desktop stand
8 Network
adapt
er cable (blue
tips)
1
Install Software
2
Plug in Network Adapter
Q)
Internet access is required for installation.
When
p
rompted to plug
in
the network adapter
1)
Plug one end of the
b
lue cable connector into the network adapter.
la) Then, plug the network
adapter
into the power outlet.
1)
Insert
the Software Install CD and
follow
the instructions
during the install.
The installer will check for the latest version of the software.
Alternatively,
you can download the latest version at
www.logitech.com/downloads.
2) You may be asked to reboot the PC.
3) Logitech Alert Commander software will
ope n.
4)
The First Run Wizard will guide you through the next steps
of setup.
4
Choose Your Camera Location
On
a
desk or table
On
a
window looking in
Clean the window's su rface and the inside area
of the suction cup before applying it to the
window. Periodically press the suction cup
against the g lass to st rengthen its bond to the
window.
$
I
Using In-the-box Accessories
You can use
the
mi ni-suction cup and
cable wall
clip
s
t
o
help route
the power
supply c
able
(yellow con nector) along
t he
window's
edge and provide
add
i-
t io nal
security to
tha
t camera.
CD
2) Connect the ot
her
blue cable connec
t
or
1nto
an
open port on your router.
Wa
rnin
g
Using
camera to
look out
a window
On ly use for non-n ight vis ion applications or when a
secondary outdoor lighting source is available. Infrared
illumination used in night vision cameras cannot penetrate
glass and can adversely affect picture quality
You can turn off night vision in the Settings > Camera>
Advanced>Night Vision Off
Before you begin ..
.
1) Read a ll instructions before
beginning the installation
2) Dunng installation. we will test you
r
PC's firewall settings. If prompted to
a llow Logitech Alert access to the
network, you should always answer
"Yes" or "Allow"
3
Plug in Your Camera
When prompted
t
o connect
your
camera:
CD
Network Adapter
I
Power Supply Insta ll Note
Caution should be used w hen plugging the Log itech Ale rt network adapter o
r
camera
power supply into a surge protector. power st rip, extension cord o
r
UPS ( un-interuptable
power supply) because they may
filter.
interfere with o
r
even block signal transmission
.
To
eliminate any potent1a
l 1
ssues we recommend pl ugg1ng the
net wor
k
adapter
or power
supply directly 1nto your wal
l
outlet
Note: Logitech Alert network adapters and power supplies have their own b
uilt
-in surge
p ro
t
ectors
1)
Remove the hatch from the back of the camera. la) Pl ug the
yellow cable
connector int
o the port
l
b) Use the lock slider to
lock the connector in place
2) Plug
the
yel low cable
connector int
o the
power
supply port.
2a) Plug the power supply
in
to
an
outle
t
near the PC where the
software is
inst
al led.
2.
0
. .
~
1.1
Shortly after connecting, your camera will appear in Alert Com-
mander software. You can now move the camera to its desired
location
Wall/Ceiling Mounting Instructions
2b
2a
On a wall or ceiling
The wall mount allows you to easily fasten
your camera to a ceiling
,
wall. or flat surface.
1)
St
art by pre-drilling holes into the
wal
l
and screwing in the mounting
base.
2a) Thread the ball jo1nt into the
camera.
OR
2b) Place the ball joint end into the wall mount
c lamp and tighten, using the
wing
nut
3) Attac
h
the camera to the mounting arm

Advertisement

loading