1. Manuals
  2. Brands
  3. Toro Manuals
  4. Tractor Accessories
  5. Z MASTER 79402
  6. Operator's manual

Toro Z MASTER 79402 Operator's Manual

52” vac–bagger for z-118 and 616/620 zero radius tractors
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FORM NO. 3319–489
Z MASTER
52" Vac–Bagger
for Z-118 and 616\620
Zero Radius Tractors
Model No. 79402 – 790001 & Up
Operator's Manual
IMPORTANT: Read this manual carefully. It contains information about your
safety and the safety of others. Also become familiar with the controls and
their proper use before you operate the product.

Advertisement

Table of Contents
loading

Related Manuals for Toro Z MASTER 79402

Summary of Contents for Toro Z MASTER 79402

  • Page 1 FORM NO. 3319–489 Z MASTER 52” Vac–Bagger for Z-118 and 616\620 Zero Radius Tractors Model No. 79402 – 790001 & Up Operator’s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety of others. Also become familiar with the controls and their proper use before you operate the product.
  • Page 2 Read this manual carefully to learn how to operate and maintain your product correctly. Reading this All of us at Toro want you to be completely satisfied manual will help you and others avoid personal injury with your new product, so feel free to contact your and damage to the product.

  • Page 3: Table Of Contents

    Contents Page Page Operation ......Safety and Instruction Decals ....General Operating Instructions .

  • Page 4: Safety And Instruction Decals

    Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. ON BLOWER HOUSING ON BLOWER (Part No. 93–1122) MOUNTING PLATE (Part No.

  • Page 5: Installation

    Installation Loose Parts Note: Use the chart below to verify all parts have been shipped. DESCRIPTION QTY. Blower deflector Hex bolt – 5/16”-18 x 3/4” (19 mm) Install deflector to mower deck Locknut – 5/16”-18 Blower assembly Dual pulley Spindle-long Install blower to mower V-Belt Hex bolt –...

  • Page 6: For Optimum Performance With Your Vacuum Bagger

    Weight Kit when equipped with a Vacuum with your Vacuum Bagger Bagger Attachment. For optimum performance, Toro recommends that The tractor requires two Front Weight Kits you install a High-lift Blade Kit (p/n 56–2390) and a when equipped with both a Vacuum Bagger Front Baffle Kit (p/n 68–7210) on the mower deck...

  • Page 7: Mower Preparation

    Installation Mower Preparation Position the deflector underneath the mower and align the front deflector mounting hole with the drilled hole in the mower. For ease of marking and assembly of vacuum bagger remove mower from traction unit. Fasten the deflector to the mower with 5/16”-18 x 3/4”...
  • Page 8 Installation IMPORTANT: Blower must fit over discharge Remove the belt, nut and washer from the opening of mower; adjust blower flange to right-hand blade spindle. Remove the single assure this condition. pulley and slide short spindle out of the spindle housing (Fig.
  • Page 9 Installation 11. Complete fastening the deflector to the front and 12. Remove outside spindle mounting bolt, file hole rear of mower with (2) 5/16”-18 x 3/4” (19 mm) square and re-install carriage bolt from the bolts and locknuts (Fig. 5). bottom (Fig.

  • Page 10: Installing The Blower

    Installation 15. Slide new long spindle up from the bottom into Installing the Blower housing. Install the new double pulley with the larger diameter pulley on bottom and secure with Fasten the spring clip to the deck using a existing washer and nut.(Fig. 8). 3/8”-16 x 3/4”...
  • Page 11 Installation Install the blower assembly onto the mower deck Remove hardware securing right fender to using six (6) 5/16”-18 x 3/4” (19 mm) bolts and footrest. Save for installing spring bracket. locknuts. Insert the hex bolts from the bottom of Fasten spring bracket below footrest using the deck (Fig.
  • Page 12 Installation Raise the mower to the highest height-of-cut and 10. Position the 1” x 2-1/2” 25 x 64 mm) flat plate install the spring between spring bracket and underneath the shield with the flat washer and spring clip. Adjust the position of the spring clip locknut above the shield (Fig 14).

  • Page 13: Installing The Canister

    Installation Installing the Canister Align the canister support over the bagger mount tubes and slide down (Fig. 16). Assemble the support bracket into the bagger Assemble the spring anchor bolts to the canister mount with (2) 3/8”-13 x 3/4” (19 mm) bolts and support brackets.

  • Page 14: Installing The Hose

    Installation Raise the top and install the canister. Lower the Position the tie strap in the groove in the top top assembly and latch in place (Fig. 17). assembly inlet. Pull the tie strap tight to secure the seal to the top assembly, then cut off the loose end (Fig.

  • Page 15: Operation

    Operation Become familiar with all operating instructions and The vacuum attachment is designed to operate safety suggestions contained in applicable Operator’s efficiently at normal mowing speed. Due to the extra amount of power required to drive the Manual before attempting to operate this equipment. mower and vacuum, it may be necessary to Never do any maintenance or repairs while the engine reduce the machine ground speed to keep the...

  • Page 16: Emptying The Canister

    Operation Emptying the Canister Move the transmission levers into the neutral position, apply the parking brake and disengage the PTO. Stop the engine before leaving the operator position. Open the latch and lift the top assembly to remove or look inside the canister. Remove the canister from the canister support and empty if full (Fig.

  • Page 17: Maintenance

    Maintenance Service Interval Chart Each Storage Service Operation Notes Hours Hours Service Replace if Blower wear strip – inspect necessary Replace if Belts – check for wear/cracks necessary Blower pulley idler arm – grease Replace if Wash discharge hose and adapter cracked or broken Canister –...

  • Page 18: Replacing The Drive Belt

    Maintenance Greasing the Blower Pulley Replacing the Drive Belt Idler Arm Remove the belt covers and note the belt routing (Fig. 23). Lubricate the blower pulley idler arm every 25 operating hours with # 2 multi-purpose lithium Remove the worn drive belt (Fig. 23). grease.

  • Page 19: Replacing The Blower Wear Strip

    Maintenance Replacing the Blower Wear Strip Remove the adaptor from the blower. Remove the five (5) locknuts, washers and carriage bolts and pull the wear strip from the blower (Fig. 24). Clean the inside of the blower thoroughly (Fig. 24). Slide the new wear strip inside the blower and install the three (3) lower carriage bolts, washers and locknuts.

Table of Contents