Table of Contents
Advertisement
Quick Links
Register at www.Toro.com.
Original Instructions (EN)
8-Blade, 11-Blade, and 14-Blade
DPA Cutting Unit
For Greensmaster
Traction Unit
Model No. 04651—Serial No. 316000001 and Up
Model No. 04653—Serial No. 316000001 and Up
Model No. 04655—Serial No. 316000001 and Up
Form No. 3397-913 Rev C
®
3300 or 3400 Series
*3397-913* C
Advertisement
Table of Contents
Related Manuals for Toro 04651
Summary of Contents for Toro 04651
- Page 1 DPA Cutting Unit For Greensmaster ® 3300 or 3400 Series Traction Unit Model No. 04651—Serial No. 316000001 and Up Model No. 04653—Serial No. 316000001 and Up Model No. 04655—Serial No. 316000001 and Up *3397-913* C Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Note emphasizes general information Whenever you need service, genuine Toro parts, or worthy of special attention. additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 Contents identifies the location of the model and serial numbers on the product. -
Page 3: Safety
• Use your full attention while operating the • Use only accessories, attachments, and machine. Do not engage in any activity that replacement parts approved by Toro. causes distractions; otherwise, injury or property damage may occur. Blade Safety • Do not put your hands or feet near moving components of the machine. -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal137-9706 137-9706 1. Cutting hazard of the hand or foot—shut off the engine, remove the key or disconnect the spark plug, wait for all moving parts to stop, and read the Operator’s Manual before performing maintenance. -
Page 5: Setup
(Figure The cutting unit is shipped without a front roller. Adjust to the desired height-of-cut and tighten Obtain a roller from your authorized Toro distributor the height-of-cut arm mounting fasteners. and install it on the cutting unit, as follows: Remove the plow bolt and flange locknut... -
Page 6: Product Overview
Contact your Authorized Service Dealer or authorized Toro Adjusting the Bedknife Daily distributor or go to www.Toro.com for a list of all approved attachments and accessories. Prior to mowing each day, or as required, verify proper bedknife-to-reel contact. - Page 7 This will make later adjustments easier. Note: As the reel blades continue to run against Insert a 0.05 mm (0.002 inch) shim (Toro Part the bedknife, a slight burr will appear on the front No. 125-5611) between the blade and the cutting edge surface along the full length of the bedknife edge at the point marked in step 4.
- Page 8 (Refer to the Toro Manual for Lower the roller and bolts from the sideplate Sharpening Reel and Rotary Mowers, Form No.
- Page 9 Low-cut 93-4264 4.7 to 25.4 mm (0.188 to (Optional) 1.00 inch) High-cut 94-6392 7.9 to 25.4 mm (0.312 to (Optional) 1.00 inch) Fairway 63-8610 9.5 to 25.4 mm (0.375 to (Optional) 1.00 inch) Fairway 137-0879 9.5 to 25.4 mm (0.375 to EdgeMax 1.00 inch) (optional)
- Page 10 Verify that the height-of-cut setting is correct; repeat this procedure if necessary. Adjusting the Cut-Off Bar Adjust the cut-off bar to ensure that the clippings are cleanly discharged from the reel area, as follows: Note: The bar is adjustable to compensate for changes in turf conditions.
-
Page 11: Maintenance
Ideally, take the cutting unit to your authorized Toro distributor for service. Refer to Whenever you need to tip the cutting unit to expose the Service Manual for your traction unit for complete... - Page 12 Assembling the Bedbar Install the bedbar, positioning the mounting ears between the washers and the bedbar-adjusting screw (Figure 13). Secure the bedbar to each side plate with the bedbar bolts (nuts on bolts) and 3 washers (6 total). Position a nylon washer on each side of the side-plate boss.
-
Page 13: Bedknife Specifications
Bedknife Specifications Installing the Bedknife Remove the rust, scale, and corrosion from the bedbar surface and apply a thin layer of oil to the bedbar surface. Clean the screw threads. Apply never-seize compound to the screws and install the bedknife to the bedbar. g255046 Figure 18 1. - Page 14 Relief-Grinding the Reel Bedknife Grinding Specifications The new reel has a land width of .8 to 1.2 mm (0.03 to 0.05 inches) and a 30° relief grind. When the land width gets larger than 3 mm (0.120 inch) wide, do the following: Apply a 30°...
-
Page 15: Backlapping The Cutting Unit
Backlapping the Cutting The angle that you use to grind your bedknives is Unit very important. Use the angle indicator (Toro Part No. 131-6828) and DANGER the angle-indicator mount (Toro Part No. 131-6829) to Contact with the reel or other moving parts check the angle that your grinder produces and then can result in personal injury. - Page 16 Notes:...
- Page 17 Notes:...
- Page 18 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 19 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.