Page 1
Form No. 3407-868 Rev A 8 and 11-Blade 27-inch and 8-Blade 32-inch Edge Series Cutting Unit Reelmaster ® 7000-D Traction Unit Model No. 03721—Serial No. 400000000 and Up Model No. 03722—Serial No. 400000000 and Up Model No. 03727—Serial No. 400000000 and Up *3407-868* A Register at www.Toro.com.
1 Inspect the Cutting Unit......... 4 2 Using the Kickstand When Tipping the Cutting You may contact Toro directly at www.Toro.com for product Unit ..............4 safety and operation training materials, accessory information, 3 Adjusting the Rear Shield ........5 help finding a dealer, or to register your product.
• To ensure optimum performance and continued safety unit is in safe operating condition. certification of the machine, use only genuine Toro • Wear appropriate clothing, including eye protection; replacement parts and accessories. Replacement parts substantial, slip-resistant footwear;...
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Cutting unit Inspect the cutting unit. Use the kickstand when tipping the – No parts required cutting unit. – No parts required Adjust the rear shield.
Installing the Loose Parts Parts needed for this procedure: Straight grease fitting O-ring Procedure The grease fitting must be installed on the reel-motor side of the cutting unit. Refer to Figure 5 to determine the position of the reel motors. g191340 Figure 3 1.
4. Install the O-ring on the reel motor (Figure g031275 Figure 9 1. Cutting unit 1 5. Cutting unit 5 g191072 2. Cutting unit 2 6. Reel motor Figure 7 3. Cutting unit 3 7. Weight 1. O-ring 4. Cutting unit 4 5.
Contact your Authorized Service Dealer or the condition of the reel and bedknife and their interaction. Distributor or go to www.Toro.com for a list of all approved After completing this procedure, always test the cutting attachments and accessories unit performance under your field conditions.
Page 8
Note: Each click turned moves the bedknife 0.022 mm (0.0009 inch). Do not overtighten the adjusting screws. 11. Test the cutting performance by inserting a long strip of cutting performance paper (Toro Part No. 125-5610) between the reel and the bedknife, perpendicular to the bedknife (Figure 13).
3. Remove the 2 nuts securing each roller bracket and soil conditions. The cutting unit setup (aggressiveness of cut, spacer to each side-plate mounting flange. rollers, bedknives, attachments installed, turf compensation settings, etc.) will also affect the effective height of cut. Check 4.
Page 10
g020410 Figure 17 1. Lift chain 3. Bottom hole 2. U bracket Groomer These are the recommended height-of-cut settings when a groomer kit is installed on the cutting unit.
Height-of-Cut Chart HOC Setting Aggressiveness of Cut No. of Rear Spacers No. of Chain Links With Groomer Kits Installed 0.64 cm (0.250 inch) Less Normal More 0.95 cm (0.375 inch) Less Normal More 1.27 cm (0.500 inch) Less Normal More 1.59 cm (0.625 inch) Less Normal...
6.35 cm (2.500 inches) Less Normal More + indicates that the U bracket, on the lift arm, is positioned in the bottom hole (Figure 17). "Y" indicates that this combination of HOC and spacers can be used with 27-inch groomers. Note: Changing 1 chain link changes the rear-roller pitch angle movement by 4.5 degrees.
Bedknife/Height of Cut Chart Bedknife Part No. Bedknife Lip Height of Cut Height * Low HOC 120-1641 5.6 mm 6.4 to 12.7 mm (Optional) (27 inch) (0.220 inch) (0.250 to 0.500 120-1642 inch) (32 inch) EdgeMax® 112-8910 6.9 mm 9.5 to 63.5 mm (Optional) (27 inch) (0.270 inch)
Page 14
Toro Manual for Sharpening Reel and Rotary Mowers (Form No. 09168SL). Important: Light contact is preferred at all times.
Maintenance Lubricating the Cutting Unit Each cutting unit has 5 grease fittings (Figure 24) that must be lubricated regularly with No. 2 lithium grease. The lubrication points are the front roller (2), the rear roller (2), and at the reel motor spline (1). Note: Lubricating the cutting units immediately after washing helps purge water out of the bearings and increases bearing life.
Checking the Top Grind Angle The angle that you use to grind your bedknives is very important. Use the angle indicator (Toro Part No. 131-6828) and the g027268 angle-indicator mount (Toro Part No. 131-6829) to check the angle that your grinder produces and then correct for...
Servicing the HD Dual Point 3. Align the keys on flange bushings to the slots in the frame and install the bushings (Figure 34). Adjusters (DPA) 4. Install a wave washer onto the adjuster shaft and slide 1. Remove all parts (refer to the Installation Instructions for the adjuster shaft into the flange bushings in the frame the HD DPA Kit (Model No.
Roller Rebuild Tool Kit (Part No. 115-0803) roller rebuild kit. Refer to your parts catalog or contact your (Figure 35) are available for servicing the roller. The Authorized Toro Distributor for assistance. Roller Rebuild Kit includes all the bearings, bearing g007790 Figure 35 1.
Page 22
The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
Page 23
The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
Page 24
Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.