1. Manuals
  2. Brands
  3. Epson Manuals
  4. Motherboard
  5. S5U13L02P00C100
  6. User manual

Epson S5U13L02P00C100 User Manual

S1d13l02 lcd controller
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S1D13L02 LCD controller
S5U13L02P00C100
Evaluation Board User
Manual
SEIKO EPSON CORPORATION
Rev. 1.0

Advertisement

Table of Contents
loading

Related Manuals for Epson S5U13L02P00C100

Summary of Contents for Epson S5U13L02P00C100

  • Page 1 S1D13L02 LCD controller S5U13L02P00C100 Evaluation Board User Manual SEIKO EPSON CORPORATION Rev. 1.0...
  • Page 2 This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product. The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any kind of damage and/or fire caused by the use of it.

  • Page 3: Table Of Contents

    4.4.2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board ..15 LCD Panel Interface ......16 GPIO Connections .
  • Page 4 EPSON S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 5: Chapter 1 Introduction

    The S5U13L02P00C100 Evaluation Board can also connect to the S5U13U00P00C100 USB Adapter board so that it can be used with a laptop or desktop computer, via USB 2.0. The S5U13L02P00C100 Evaluation Board can be used with many native platforms via the host connector which provides the appropriate signals to support a variety of CPUs.

  • Page 6: Chapter 2 Features

    Chapter 2 Features Chapter 2 Features The S5U13L02P00C100 Evaluation Board includes the following features: • 208-pin QFP22 S1D13L02 LCD controller • Headers for connection to the S5U13U00P00C100 USB Adapter board • Header with all S1D13L02 Host Bus Interface signals (optional) Note These headers are not mounted.

  • Page 7: Chapter 3 Installation And Configuration

    Chapter 3 Installation and Configuration Chapter 3 Installation and Configuration The S5U13L02P00C100 Evaluation Board incorporates a DIP switch, jumpers, and 0 ohm resistors which allow it to be used with a variety of different configurations. 3.1 Configuration DIP Switch The S1D13L02 has 2 configuration inputs (CNF[2:1]). A DIP switch (SW1) is used to configure CNF[2:1] as described below.

  • Page 8: Configuration Jumpers

    Chapter 3 Installation and Configuration 3.2 Configuration Jumpers The S5U13L02P00C100 Evaluation Board has 2-pin jumpers (x 8) which configure various board settings. And this board has 8-pin jumper for setting backlight of the LCD panel. The jumper positions for each function are shown below.
  • Page 9 The jumper associated with each power supply is as follows: JP1 for COREVDD JP2 for PLLVDD JP3 for HIOVDD JP5 for PIOVDD JP7 for GIOVDD Figure 3-2: Configuration Jumper Locations (JP1, JP2, JP3, JP5, JP7) S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
  • Page 10 JP9 - Backlight Power Supply for LCD Panel The S5U13L02P00C100 Evaluation Board is designed to generate backlight power supply for LCD panel from 3.3V via the S5U13U00P00C100 USB adapter board or connector H1. The 3.3V must be supplied from the S5U13U00P00C100 or H1.
  • Page 11 Chapter 3 Installation and Configuration Figure 3-3: Configuration Jumper Location (JP4, JP6, JP8, JP9) S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...

  • Page 12: Chapter 4 Technical Description

    PIOVDD of S1D13L02 is the power used by the LCD interface and GPIO[23:8] and can range from 1.65V to 3.6V. However, PIOVDD of the S5U13L02P00C100 Evaluation Board can range from 3.0V to 3.6V. When JP6 is set to the 2-3 position, PIOVDD is connected to 3.3V. If a different voltage is needed for PIOVDD because of the LCD panel requirements, set JP6 to the 1-2 position and connect the external power supply to pin 2 of connector H4.

  • Page 13: Clocks

    The on-board 4MHz oscillator is not specified to work below a 3.0V supply voltage. 4.3 Reset The S1D13L02 LCD controlleron the S5U13L02P00C100 Evaluation Board can be reset using a push-button switch (SW2), or via an active low reset signal from the host development platform (pin 33 on the H1 connector).

  • Page 14: Host Interface

    4.4 Host Interface 4.4.1 Direct Host Bus Interface Support All S1D13L02 host interface pins are available on connector H1 which allows the S5U13L02P00C100 Evaluation Board to be connected to a variety of development platforms. For detailed S1D13L02 pin mapping, refer to the S1D13L02 Hardware Functional Specification, document number XB0AA001.

  • Page 15: Connecting To The Epson S5U13U00P00C100 Usb Adapter Board

    When the S5U13L02P00C100 is connected to the S5U13U00P00C100 USB Adapter board, there are 2 LEDs on the S5U13L02P00C100 which provide a quick visual status of the USB adapter. HB (D300)blinks to indicate that the USB adapter board is active. ENUM (D301)turns on to indicate that the USB has been enumerated by the PC.

  • Page 16: Lcd Panel Interface

    Connector H2 and H3 are not mounted. H2 and Figure 4-4: LCD Panel Connectors Location (H2, H3, H4) For the pinout of connectors H2, H3,H4 and H5, see Section Chapter 6, “Schematic Diagrams” on page 20. EPSON S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 17: Gpio Connections

    The GPIO[7:0] pins only function as GPIOs and are powered from GIOVDD. All the GPIO pins are available on the H3 and H4 connectors. Note that connector H4 is not populated on the S5U13L02P00C100 Evaluation Board. Connector H3 is a 0.1” x 0.1”, 40-pin header and connector H4 is a 0.1” x 0.1”, 16-pin header (8 x 2). The following figure shows the location of the connector H3 and H4.

  • Page 18: Chapter 5 Parts List

    Steward HZ0603B751R-10 OHMS 0603 SMD R0603 TDK VLCF5020T- 22uH Fixed inductor 220MR75-1 P1, P2 HEADER_20X2 HDR2X20/2MM 3M 151240-8422-RB R1, R2, R19 R0402 R3, R6 R0603 150k 1% R0402 R5, R7, R8 R0402 EPSON S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0)
  • Page 19 MINIATURE SMT Keystone 5015 TP_1206 S1D13L02 LCD controller Epson IC 1.5V 100MA LDO REG Texas Instruments TPS76915DBVT SOT-23-5 TPS76915DBVT Texas Instruments TPS61161ADRVT TPS61161ADRVT OSC 4.0000MHz 3.3V 4M OSC EPSON SG-636 50ppm SMD S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...

  • Page 20: Chapter 6 Schematic Diagrams

    Chapter 6 Schematic Diagrams Chapter 6 Schematic Diagrams Figure 6-1: S5U13L02P00C100 Schematics (1 of 3) EPSON S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0)
  • Page 21 Chapter 6 Schematic Diagrams Figure 6-2: S5U13L02P00C100 Schematics (2 of 3) S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
  • Page 22 Chapter 6 Schematic Diagrams Figure 6-3: S5U13L02P00C100 Schematics (3 of 3) EPSON S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 23: Chapter 7 Board Layout

    Chapter 7 Board Layout Chapter 7 Board Layout Figure 7-1: S5U13L02P00C100 Board Layout - Top View S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
  • Page 24 Chapter 7 Board Layout Figure 7-2: S5U13L02P00C100 Board Layout - Bottom View EPSON S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 25: Chapter 8 References

    Chapter 8 References Chapter 8 References 8.1 Documents • Epson Electronics America, Inc., S1D13L02 Hardware Functional Specification, document number XB0A-A- 001. 8.2 Document Sources • Epson Electronics America Website: http://vdc.epson.com. S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
  • Page 26 Chapter 8 References Change Record EPSON S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0)
  • Page 27 Chapter 8 References S5U13L02P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
  • Page 28 80992 Munich, GERMANY Hi- Tech Park, Shenzhen Phone: +49-89-14005-0 FAX: +49-89-14005-110 Phone: +86-755-2699-3828 FAX: +86-755-2699-3838 EPSON TAIWAN TECHNOLOGY & TRADING LTD. 14F, No. 7, Song Ren Road, Taipei 110 Phone: +886-2-8786-6688 FAX: +886-2-8786-6660 EPSON SINGAPORE PTE., LTD. 1 HarbourFront Place,...

Table of Contents