Advertisement
Quick Links
Advertisement
Related Manuals for Husqvarna LH 700
Summary of Contents for Husqvarna LH 700
- Page 1 LH 700, LH 804 Operator's manual 2-32...
- Page 2 Technical data.............. 26 Operation..............10 Registered trademarks..........30 Maintenance..............18 EC Declaration of Conformity........31 Introduction Product overview (LH 700) To do a check of the vibration damping units on 1. Ignition lock page 9 . 2. Handle 3. Throttle control 11.
- Page 3 Product overview (LH 804) Remote control overview 1. Lifting point 2. Safety frame 3. Drain plug for engine oil 4. Safety straps 5. Eccentric element 6. Type plate 7. Vibration damping units 8. Water separator 9. Hydraulic oil tank 10. Battery charger for the remote control 1.
- Page 4 Be careful and use the product correctly. LH 700: Risk of injury if the handle falls on you. Lock the handle in the lifted position. Read the manual carefully and make sure that you understand the instructions before you use the product.
- Page 5 Type plate 5. Manufacturer 6. Rated power 7. Production year Product liability As referred to in the product liability laws, we are not liable for damages that our product causes if: • the product is incorrectly repaired. • the product is repaired with parts that are not from the manufacturer or not approved by the manufacturer.
- Page 6 • Make sure that only approved persons are in the control in the transport position behind the rear work area. cover. Lock the rear cover with a padlock. This makes sure that the product cannot be used by • Keep the work area clean and bright. persons that are not approved.
- Page 7 Do a check of the safety devices regularly. If the where exhaust fumes can easily collect. safety devices are defective, speak to your Noise safety Husqvarna service agent. Emergency stop button WARNING: Read the warning instructions The emergency stop button is used to quickly stop the that follow before you use the product.
- Page 8 To do a check of the emergency stop button (LH 700) To do a check of the emergency stop button on the remote control (LH 804) 1. Turn the emergency stop button clockwise to make To start the product sure that it is disengaged.
- Page 9 If the battery • Make sure that the vibration damping units are has a deformation or is damaged, speak to correctly installed. an approved Husqvarna service agent. • Examine the vibration damping units for damages and wear. •...
- Page 10 Do the daily maintenance. Refer to schedule on page 18 . To set the handle to operation position (LH 700) WARNING: Hold the handle tightly when you change the position of the handle. There is a risk of injury if the handle falls on you.
- Page 11 To adjust the handle height (LH 700) 2. Make sure that the emergency stop button is disengaged. 1. Loosen the screw (A). 3. Turn the ignition key to the ignition position (A). The indicators for battery charge and oil pressure come 2.
- Page 12 The indicator for battery charge (B) comes on if the battery does not charge correctly. 5. Turn the ignition key to the stop position (A). To operate the product (LH 700) Always operate the product with the throttle control set to full throttle.
- Page 13 LED indicator Cause LED indicator Cause Flashes green quickly. The remote control is not Flashes green slowly. The remote control is con- connected to the receiver. nected to the receiver. Flashes green slowly. The remote control is con- On with a yellow light. The battery charge is low.
- Page 14 location only, in the temperature range -25– 2. Put a battery (A) into the remote control. 70°C/-13–158°F. The desktop charger operates in the voltage range 100– 240 V. The desktop charger has an adapter that can be used in most power sockets. The time to fully charge the battery is 2.5 hours at correct temperature.
- Page 15 5. Move and hold the joystick (A) on the remote control 1. Connect the cable (A) to the receiver. away from center position. 2. Connect the cable to the remote control. 6. Turn the start/stop button (B) clockwise to start the remote control.
- Page 16 2. Move the joystick to move the product in that Event Information on the display direction: ® Bluetooth ® Bluetooth connected "Pairing info" "Pairing RX-TX- Link OK" ® Bluetooth fault "Pairing info" "Pairing RX-TX- Link ER- ROR" a) Forward operation (A). "Pairing failed!"...
- Page 17 5. Turn the start/stop button (C) clockwise to start the remote control. There is no radio communication between the remote control and the receiver. The temperature of the hydraulic oil is too 6. Push the button (D) to connect the remote control to high.
- Page 18 5. Push the start/stop switch (C) down to stop the 7. Push the stop button (A) to stop the remote control. engine. The buzzer starts. The LED indicator on the remote control goes off. 6. Open the rear cover and turn the battery switch (A). The buzzer (B) stops.
- Page 19 Engine maintenance Before use, After the Weekly, Yearly, each each 10 h first 20 h each 100 h 300 h Clean the air filter. Replace the engine oil. Clean the oil filter. Replace the air filter. Do a check of the fuel injection pump. Do a check of the fuel injection nozzle.
- Page 20 dust in the air filter is dangerous to your 2. Remove the oil drain plug and connect a hose (A). health. WARNING: Do not clean the air filter with compressed air. This causes damage to the air filter and the risk increases that you breathe the dangerous dust.
- Page 21 • Use a voltage-regulated battery charger for gel Recommended battery chargers batteries. Refer to (LH 804) on page 21 . Speak to your Husqvarna dealer for more information about the correct battery charger. • If the battery is not used for a long period of time, charge it fully before you use it.
- Page 22 Fuses (LH 804) b) Remove the screw and washer (C) and install a ring bolt of type M16x1.5 in the hole. c) Attach lifting equipment to the ring bolt and lift the eccentric element. d) Put the eccentric element on a stable surface. 2.
- Page 23 Hydraulic system 1. Remove the protective cover (A) on the hydraulic oil tank. To do a check of the hydraulic hoses • Examine the hydraulic hoses regularly. Replace worn or damaged hydraulic hoses. WARNING: Hydraulic oil is dangerous. The rubber in the hydraulic hoses wears with time.
- Page 24 WARNING: Do not walk or stay below or near a lifted product. 1. Lock the handle in upright position (model LH 700 only). 2. Attach the lifting equipment to the lifting eye. To safety the product to a transportation vehicle with tie-down straps (LH 804) 1.
- Page 25 Obey the local recycling requirements and applicable regulations. • Do not discard the battery as domestic waste. • Send the battery to a Husqvarna service agent or discard it at a disposal location for used batteries. 1177 - 001 - 02.04.2020...
- Page 26 Technical data Technical data LH 700 LH 804 Operation weight (EN500, incl. oil, ½ fuel), kg/lb 779/1717 820/1808 Engine brand, type Hatz, 1 D90V Hatz, 1 D90V Engine power, kW/hp @rpm 11.5/15.4 @3000 11.5/15.4 @3000 Vibration frequency, Hz/rpm 56/3000 56/3000 Amplitude, mm/in.
- Page 27 Noise and vibration emissions LH 700 LH 804 Sound power level, guaranteed L dB (A) Sound pressure level at the operator's ear, L , dB (A) Vibration level, a , m/s N/A (remote control) Weights for options Extensions 2 units per machine, 2 x 75 mm/6 in. kg/Ib 14.6/32...
- Page 28 ® Radio frequency data for Bluetooth Frequency band, GHz 2.4-2.4835 Output power, max. dBm Noise and vibration declaration statement These declared values were obtained by laboratory type testing in accordance with the stated directive or standards and are suitable for comparison with the declared values of other products tested in accordance with the same directive or standards.
- Page 29 Product dimensions (LH 700) Handle height, transport Length including handle, 1320/51 1880/74 position, mm/in. mm/in. Handle height, operation Height, mm/in. 1170/46 795/31 position, mm/in. Bottom plate contact area, Width, mm/in. 0.290/3.12 660/26 /sq. ft. Bottom plate contact area 0.646/36.95 or...
- Page 30 Bluetooth SIG, inc. and any use of trademarks owned by such marks by Husqvarna is under license. LOCTITE is a registered trademark owned by Henkel Corporation. N243 is a trademark of Henkel Corporation. 1177 - 001 - 02.04.2020...
- Page 31 EC Declaration of Conformity EC Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Reversible Plate Compaction Machine Brand Husqvarna Type/Model LH 700 Identification Serial numbers dating from 2020 and onwards...
- Page 32 EC Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Reversible Plate Compaction Machine Brand Husqvarna Type/Model LH 804 Identification Serial numbers dating from 2020 and onwards complies fully with the following EU directives and...
- Page 33 1177 - 001 - 02.04.2020...
- Page 34 1177 - 001 - 02.04.2020...
- Page 35 1177 - 001 - 02.04.2020...
- Page 36 www.husqvarnacp.com Original instructions 1140393-26 2020-04-09...