Download
Share
Print this page
Husqvarna LT 5005 Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Vibratory rammers & tampers
  5. LT 5005
  6. Operator's manual

Husqvarna LT 5005 Operator's Manual

Hide thumbs Also See for LT 5005:

Advertisement

Quick Links

LT 5005, LT 6005
EN
Operator's manual
2-23

Advertisement

loading

Related Manuals for Husqvarna LT 5005

Summary of Contents for Husqvarna LT 5005

  • Page 1 LT 5005, LT 6005 Operator's manual 2-23...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Transportation, storage and disposal......14 Safety................5 Technical data.............. 17 Operation................ 9 EC Declaration of Conformity........21 Maintenance..............10 Warranty............... 22 Introduction California Proposition 65 WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
  • Page 3 Product overview Throttle control 1. Fuel tank 2. Locking knob for the cover The throttle control has 3 available positions: 3. Hour meter • Operation mode position (A) 4. Vibration damping units • Start position / idle speed position (B) 5.
  • Page 4 Read the manual carefully and make sure that you understand the instructions before Set throttle control in start position. you use the product. Air filter indicator. Choke closed. Use hearing protection. Push the primer bulb 5 times. Use protective boots. Pull the starter rope handle.

  • Page 5: Safety

    • the product is incorrectly repaired. • the product is repaired with parts that are not from the manufacturer or not approved by the manufacturer. • the product has an accessory that is not from the manufacturer or not approved by the manufacturer. •...
  • Page 6 fall and there is a risk of injury and damage to the can increase gradually during weeks, months or product. years. Possible injuries include damage to the blood circulation system, the nervous system, joints, and • Do not use the product in areas where fire or other body structures.
  • Page 7 Do not use a product with defective safety devices. Noise safety • Do a check of the safety devices regularly. If the safety devices are defective, speak to your Husqvarna service agent. WARNING: Read the warning instructions that follow before you use the product. Safety frame •...
  • Page 8 To do a check of the vibration damping system • Do not fill the fuel tank fully. Heat causes the fuel to expand. Keep a space at the top of the fuel tank. 1. Make sure that there are no cracks or deformation •...

  • Page 9: Operation

    Operation Introduction 2. If the engine is cold, push the primer bulb 5 times. WARNING: Read and understand the safety chapter before you use the product. To do before you operate the product • Read the operator's manual carefully and make sure that you understand the instructions.

  • Page 10: Maintenance

    To operate the product To stop the product 1. Set the throttle control in the operation position. • Set the throttle control in the stop position. 2. Hold the handle and move the product in the necessary direction. CAUTION: Do not push the product down.
  • Page 11 General product maintenance Before use, After the Weekly, Yearly, each each 10 h first 20 h each 100 h 500 h Replace the oil in the rammer leg. Tighten the bolts on the rammer shoe. Examine the vibration damping units for damage. Examine the cover knob for damage.
  • Page 12 3. Clean the oil from the dipstick. 3. Tilt the product and let the oil run out into the container. 4. Put the dipstick back fully into the oil tank. 5. Remove the dipstick. 6. Examine the oil level on the dipstick. 7.
  • Page 13 6. Fill with new oil through the hole for the sight glass. 1. Examine the air filter indicator. If the air filter Technical data on page 17 for the correct Refer to indicator is on red, it is necessary to replace the air type of oil.

  • Page 14: Transportation, Storage And Disposal

    To move the product on the transport wheels To install and remove the transport device 1. Set the throttle control in the stop position. (LT 5005) 1. Set the throttle control in the stop position. 2. Lift the handle to tilt the product away from you.
  • Page 15 3. Use your foot to put the transport device between • Attach the lifting equipment at the lifting point of the the rammer shoe and the lift handle on the rammer safety frame. A label on the product identifies the leg.
  • Page 16 Discard all chemicals, such as engine oil or fuel, at a service center or at an applicable disposal location. • When the product is no longer in use, send it to a Husqvarna dealer or discard it at a recycling location. 957 - 002 - 14.10.2019...

  • Page 17: Technical Data

    Technical data Technical data LT 5005 LT 6005 Rammer leg Rammer leg Rammer leg Rammer leg width 153 mm/6 width 230 mm/9 width 230 mm/9 width 280 mm/11 in. Weight with empty tanks, kg/lb 60/132.3 61/134 68/149 69/151 Operation weight (EN500, incl. oil, ½...
  • Page 18 Noise and vibration emissions LT 5005 LT 6005 Sound power level, guaranteed L dB (A) Sound pressure level at the operator's ear, L , dB (A) Vibration level, a , m/s Noise and vibration declaration statement These declared values were obtained by laboratory type...
  • Page 19 Product dimensions LT 5005 Rammer shoe contact 0.034/0.36 / Height, mm/in. 1030/40.6 area, m /sq. ft. 0.053/0.57 Rammer shoe length, Rammer shoe width, 330/13 153/6 / 230/9 mm/in. mm/in. Length, mm/in. 726/28.6 Width, mm/in. 345/13.6 Handle height, mm/in. 910/35.8 957 - 002 - 14.10.2019...
  • Page 20 Product dimensions LT 6005 Rammer shoe contact 0.053/0.57 / Height, mm/in. 1084/42.7 area, m /sq. ft. 0.065/0.70 Rammer shoe length, Rammer shoe width, 330/13 230/9 / 280/11 mm/in. mm/in. Length, mm/in. 726/28.6 Width, mm/in. 345/13.6 Handle height, mm/in. 935/36.8 957 - 002 - 14.10.2019...

  • Page 21: Ec Declaration Of Conformity

    EC Declaration of Conformity EC Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Rammer Compaction Machine Brand Husqvarna Type/Model LT 5005, LT 6005 Identification Serial numbers dating from 2019 and onwards...

  • Page 22: Warranty

    WHAT IS COVERED YOUR WARRANTY RIGHTS AND OBLIGATIONS REPAIR OR REPLACEMENT OF PARTS: Repair or The U.S. EPA and Husqvarna Construction Products replacement of any defective warranted part will be North America Inc. (HCP) are pleased to explain the performed at no charge to you at an HCP authorized evaporative emission control system warranty on your service center.
  • Page 23 WHERE TO GET WARRANTY SERVICE Evaporative emission control system Warranty services or repairs are provided at all HCP authorized service centers. To find your nearest HCP authorized service center, go to the HCP website. REPAIR AND REPLACEMENT OF EVAPORATIVE EMISSION-RELATED PARTS Any HCP approved replacement part used in the performance of any warranty repair or replacement on evaporative emission-related parts, will be provided...
  • Page 24 www.husqvarnacp.com Original instructions 1140374-26 2019-10-30...

This manual is also suitable for:

Lt 6005