Part Tone; Ton Filter (Tone Filter); Mix Level - Yamaha CS6X Owner's Manual

• If PartAD (A/D Input Part) has
been selected
An audio source connected to the A/D INPUT jack can
be used as a Part. There are 13 different templates for
Effect Type and Gain settings. Select the A/D Input
Part source and the template.
MIXíTemplate)Src Number
PartAD keybaord
Src (Source)
Select the source connected to the A/D INPUT jack.
Settings: mic (microphone), guitar, keyboard, audio
Number (Template Number)
Select the Template Number. You can choose from
13 templates for each source.
Settings: 0 ~ 12
Number
0 1
Src
MIC PresetName Off Mic
InputGain mic mic
VariType - -
GUITAR PresetName Off Guitar
InputGain mic mic
VariType - -
KEYBOARD PresetName Off Keyboard
InputGain line line
VariType - -
AUDIO PresetName Off Audio
InputGain line line
VariType - -
Number
7 8
Src
MIC PresetName Karaoke3 Echo
InputGain mic mic
VariType Karaoke3 Echo
GUITAR PresetName FlangGtr CleanGtr
InputGain mic mic
VariType Flanger1 Celeste3
KEYBOARD PresetName WahClavi RotaryOrg
InputGain line line
VariType TouchWah1 RotarySp.
AUDIO PresetName Audio Audio
InputGain line line
VariType - -
If the InsEF parameter of the EFF Part screen is set to
something other than PartAD, "InsEF Off" will be
displayed and this parameter will not be available.

MIX Level

You can set output level, pan, effect send and other
parameters for each Part. This is useful when setting
up the levels of each Part in a mix.
MIXíLevel) Vol
Part01 127
--[InsEF off ]
2 3 4 5 6
Reverb Chorus Cho+Rev Karaoke1 Karaoke2
mic mic mic mic mic
- - - Karaoke1 Karaoke2
Reverb Chorus Cho+Rev Tube Stack
mic mic mic mic mic
- - - AmpSim. AmpSim.
Reverb Chorus Cho+Rev PhaserEP PanEP
line line line line line
- - - Phaser1 AutoPan
Reverb Chorus Cho+Rev Audio Audio
line line line line line
- - - - -
9 10 11 12
Vocal Studio OctUp OctDown
mic mic mic mic
Stage1 Exciter PitChange1 PitChange1
FuncGtr Tremolo Phaser 5thGuitar
mic mic mic mic
TouchWah2 Tremolo Phaser1 PitChange1
SynthStr SynthPad SynthLead SFX
line line line line
Symphonic Flanger2 DelayLCR PitChange1
Audio Audio Audio Audio
line line line line
- - - -
Pan RevSend ChoSend
C 64 0
Vol (Volume)
Set the output level of the Part.
Settings: 0 ~ 127
Pan
Set the stereo pan position of the Part.
Settings: L63 (Left) ~ C (Center) ~ R63 (Right)
RevSend (Reverb Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the bypassed signal) to the Reverb
effect.
Settings: 0 ~ 127
ChoSend (Chorus Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the bypassed signal) to the Chorus
effect.
Settings: 0 ~ 127

Part Tone

You can set Filter, Envelope Generator and other
parameters controlling the tonal characteristics of each
Part. The following four screens are available.

TON Filter (Tone Filter)

TON EG (Tone Envelope Generator)
TON Portamento (Tone Portamento)
TON Other (Tone Other)
TON Filter (Tone Filter)
You can use filters to adjust the tone of each part. If
the filter is an LPF and HPF combination, the Cutoff
parameter applies to the LPF.
TONíFilter)
Part01
This screen is not available for the A/D Input Part.
Details about the Filter are given on Page 93.
Cutoff
Raise or lower the Cutoff frequency for each
Element of a Part.
For each Element, if a combined Low Pass and High
Pass Filter is being used, this parameter adjusts the
Cutoff frequency of the Low Pass Filter.
Settings: -64 ~ 0 ~ +63
130
Cutoff Reso
+63 +63