Table of Contents
Advertisement
Programme item is used in order to store the channels after
Autostore, as from a required programme. In default the pro-
gramme number is set to the following programme after the
last set programme. By using “ ” or “ ” button the number
can be changed, in addition to change number digit button or
double digit button can be used too.
If your TV has more then one Standard option you may
change it by using “ ” or “ ” button to BG, DK or L/L’ on
“STANDARD” item.
To cancel AUTOSTORE before starting, press “
To select “START” use “ ” or “ ” button and press “ ” or
“ ” button. To cancel AUTOSTORE during running press “ ”
or “ ” button.
After Autostore is finalized, a programme list will apper on the
screen. In the programme list you will see the programme num-
bers and names assigned to the programmes.
If you do not accept the locations and/or the programme names
of programmes, you can change them in Programme menu.
Other Features
TV Status
Programme Number, Programme Name (or AV), (they
are displayed on the upper left of the screen) and Sleep
Timer (shows the time left on the upper right screen if en-
abled). They are displayed after programme change during 3
seconds.
Programme Number
Programme Name (5 characters)
These OSD’s are displayed when a new programme is en-
tered by digit button, by pressing "
or “- P/CH ” button, or by “
Flash back (
This button is used to return to the previous viewed preset.
By pressing the "
gle between two presets.
Double-digit (- / - -)
This OSD is displayed when the "- / - -" button pressed in
place of the programme number indicator.
After then, in order to enter a programme it must be pressed
to two digit consecutively. When it is late to press any digit
button this function will be ignored and the display will be
erased. In the same way it must not be late to press any dig-
it button after entering the first digit. The limit of the delay
time is 3 seconds.
Picture Mode
The picture mode OSD is displayed below the sound indica-
tor.
Downloaded from:
http://www.usersmanualguide.com/
" button, or by “ P/CH+“
79
” button.
)
" button repeatedly it is possible to tog-
By pressing “
be switched into 4:3, 16:9 or Auto(only AV1) mode.
Sleep Timer Last Minute Indicator
It is displayed on the upper right of the screen. If sleep timer
is activated it is displayed with the TV status and erased with
it after 3 seconds.
If there is left only one minute of the down counting of the
” button.
timer, it is displayed automatically on the upper left of the
screen, and stayed there until finishing. Then TV goes auto-
matically to stand-by.
Sound Mute
To cut off the sound from the TV press “ ” button. To restore
the sound press the “ ” button again or use the “
“-
” buttons, in this case the volume will start from mini-
mum setting.
No-Signal
No-Signal Timer Indicator
It is displayed in the middle of the screen when no valid sig-
nal detected. It shows the remained time for the switching to
the Stand-By mode (it takes 5 minutes when any signal de-
tected or no any Remote Control command is accessed).
The indicator is displayed in 3 seconds when there is no valid
signal.
After an Remote Control command (if No-Signal Timer is ac-
tive) the timer stops and if no signal detected again the timer
is initialized to 5 minutes and starts 3 seconds later again to
count down.
It is not valid in AV mode.
Blue Background During No-Signal
In case, no valid signal is detected (in TV or AV mode) Blue
Background is activated.During search process Blue Back-
ground is not active. But instead of it there is another feature
given; the semi-transparent menu background is made blue.
Volume Bar
It is displayed in the lower middle of the screen. When a vol-
ume command is received (pressing “
mote Control or Front panel) and no menu is active, it stays
on the screen for 3 seconds, after the last volume command
or until another command is received in between.
AV Modes
By pressing the “
modes (except being in Teletext). Pressing this button con-
secutively will switch the TV in one off the AV modes:
SCART or RGB.
SCART supports the RGB mode. But if there is some colour
problem in SCART modes, please force the AV mode to RGB
mode.
In order to quit the AV mode press the “
- 12 -
” wide mode button, the picture mode can
+” or “-
(;7
“ button you can switch your TV to AV
79
” button.
+” or
” by Re-
Advertisement
Table of Contents
