4 | TCE 260 | Content English Outline Operation notice General provision Separate the tire edge Technical Parameter Rim location direction Application range Fixed the tire Machine diagram Demount tire Mount the tire Safety requirements and notes 6.10 The process for mount/ demount...
Outline | TCE 260 | 5 Outline Notes General provision The pictures in the manual all comes from the original 1. This instruction is essential part for products. Please design structure of the machine. The structure shown carefully read the warnings and instructions inclu-...
6 | TCE 260 | Outline Machine diagram 4. Decompression system Decompression system Warning Decompression tool Bead breaker blade Understand all the information related to the machi- Fixed style Manual ne; understand how to prevent the appearance of the Enter style Manual accident;...
Safety requirements and notes | TCE 260 | 7 Machine nameplate 4. The machine should be kept away from the inflam- Each machine is equipped with the appointed mable and explosive materials. It should also be kept technical parameter and serial number.
8 | TCE 260 | Transports Transport method Do not detach the bolts, nuts or the other compo- nents from the machine; As shown in the figure, Before cut off the power supply, you must not contact the motor and the live parts on the machi- ne such as power cord;...
Unpacking | TCE 260 | 9 Transports 1. Hoist up the machine from the pallet. Bind the hoist tape (mod.DR 750 of 3 m and DR 735 of 1.5 m factor 6:1 ). Hoist tape requirement: more than 1 metric ton and safety factor 6:1.
10 | TCE 260 | Installation Fixed the cover then fasten the bolt. Loosen the anchor bolt, push the cross arm to the innermost position, prepare the lifting machine. Connect the air pipe, open the side panel of machine body, then make the air pipe connect with straight connector.
Installation | TCE 260 | 11 6. The work are should enjoy enough light to secure the When you do not use the machine, please switch off operators can observe each details of the operation. the power supply in time to secure the machine not to be used accidently.
12 | TCE 260 | Operation Operation Test control system 1. Pedal control system Safety notice Step down the turntable rotation control pedal 7-4, the turntable will rotate clockwise. And rise This machine is only used to mount/demount the car up the turntable rotation control pedal 7-4, the tires.
Operation | TCE 260 | 13 Special tips Operation notice 1. Special process to be need for some special tires, which different from the normal demount/ mount Warning process. 2. Some special rims as figure below, the groove at The following information must be read, which is hel- the middle of the rim is very shallow.
14 | TCE 260 | Operation Rim location direction You should be very careful when you break the How to decide from which side of the wheel to de- bead. When the blade moves, its speed is very fast and mount tire? the strength is very strong.
Operation | TCE 260 | 15 Clamp the rim from inside: Note: If there is inner tube, please turn the valve 10cm Close clamping jaw on the turntable. away to the right and then to operate. So that it can not Place the tire on the turntable, and step down the damage the inner tyre.
16 | TCE 260 | Operation Mount the tire 1. Selection the tire Before select the tire, you should know the tech- nical feature, technical parameter, characteristic and safe grade of the tire. The related information is marked on the side wall of the tire.
Page 17
Operation | TCE 260 | 17 3. Position the tool head 5. Mount the upper bead Step down the pedal 7-1 to move the tool head to Position the upper bead at the bottom end of the the original work position.
18 | TCE 260 | Inflation 6.10 The process for mount/ demount the 4. The max. inflation pressure is 3.5bar, under any cir- cumstance don't exceed manufacturer recommend special wheel pressure. Some special rims, the groove at the middle of the 5.
Transport, Storage, and Ruin | TCE 260 | 19 Storage 5. Frequently stop inflation and check the pressure in- side the tire, not exceeding 3.5bar, un-til the pressu- re inside the tire meet the requirement and avoid the If you want to store the machine for a long tire pressure not ex-ceeding the max pressure.
20 | TCE 260 | Maintenance The fault parts must be changed by the original parts 5. Periodically tighten the nut at the fixed equipment. provided by the manufacturer. 6. Periodically fill in the lubrication oil components can move and slide to each other.
Troubleshooting solution | TCE 260 | 21 8. If the lifting device moves too slow and the co- 5. Meanwhile, take the following measures: lumn tilts too slow, you should operate as per the The gloves should be oil-proof. following steps shown in figure below. Clean the Wear goggle to prevent the splash of the oil.
22 | TCE 260 | Pneumatic scheme 6. The turntable can not fix the rim Tool head cylinder air leakage/ hook without The turntable cylinder is damaged force Change the turntable cylinder; The cylinder piston is damaged/ sealing kits is bro- Change the turntable cylinder sealing kit.
Page 44
Bosch Automotive Products (Nanjing) Co., Ltd Automotive Service Solutions No.1 Runbo Road East Zone of Nanjing Economic and Technological Development Nanjing China www.bosch.com 1 987 AT7 374 | 2015-09-02...