Related Manuals for Epson S5U1C17M13T1
Summary of Contents for Epson S5U1C17M13T1
- Page 1 CMOS 16-BIT SINGLE CHIP MICROCONTROLLER S5U1C17M13T1 Manual (Software Evaluation Tool for S1C17M13) Rev.2.0...
- Page 2 2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product. The user should use it properly and in a safe manner. Seiko Epson dose not assume any responsibility or liability of any kind of damage and/or fire coursed by the use of it. The user should cease to use it when any abnormal issue occurs even during proper and safe use.
-
Page 3: Table Of Contents
1. Outline......................... 1 2. How to Use SVT17M13 ....................2 To Perform Free-Run ........................2 To Debug Software ........................2 Appendix A Circuit Diagram..................6 Appendix B Parts List ....................7 Revision History ....................... 9 Seiko Epson Corporation S5U1C17M13T1 Manual (Rev.2.0) -
Page 4: Outline
1. Outline Outline S5U1C17M13T1 (SVT17M13: Software Evaluation Tool for S1C17M13) is an evaluation board for the Seiko Epson single-chip microcontroller S1C17M13. The parts shown below are mounted on this board. S1C17M13 (MCU) Seven-segment red LED x 5 SMD orange LED x 3... -
Page 5: How To Use Svt17M13
1) Perform the same operations as in Section 2.1 to supply +5 V power to the S1C17M13 (MCU) from the PC. 2) Connect the SVT17M13 to a Seiko Epson emulator, ICDmini Ver. 2 or ICDmini Ver. 3, as shown below. - Page 6 Target connection cable connection position Flash programming power supply cable connection position ④ ⑧ ③ ⑦ ② ④ ⑥ ⑧ ⑩ ① ③ ⑤ ⑦ ⑨ Figure 2.3 Connection Example Between SVT17M13 and ICDmini Ver. 2 Seiko Epson Corporation S5U1C17M13T1 Manual (Rev.2.0)
- Page 7 USB port Mini USB connector ④ ⑧ ③ ⑦ ② ④ ⑥ ⑧ ⑩ Target connection cable ① ③ ⑤ ⑦ ⑨ connection position Figure 2.4 Connection Example Between SVT17M13 and ICDmini Ver. 3 Seiko Epson Corporation S5U1C17M13T1 Manual (Rev.2.0)
- Page 8 Debug status signal input FLASH_VCC_OUT – Flash programming voltage output – Ground TARGET_RST_OUT Target system reset signal output TARGET_VCC_IN – Target voltage input VCC3.3V – Power supply (3.3 V). Not connected on this board. – Unused Seiko Epson Corporation S5U1C17M13T1 Manual (Rev.2.0)
-
Page 9: Appendix A Circuit Diagram
Appendix A Circuit Diagram Appendix A Circuit Diagram Seiko Epson Corporation S5U1C17M13T1 Manual (Rev.2.0) -
Page 10: Appendix B Parts List
FTDI 38 U4 EEPROM BR24G128F-3GTE2 128K bits, SOP8 ROHM 39 U5 Logic SN74AHCT1G08DCKR AND gate, TTL input, SC70 40 X1 Ceramic resonator CSTCR4M00G55-R0 4.000 MHz muRata (Unmounted) 41 Z1, Z2 Chip varistor AVRL161A6R8GTA 1608 Seiko Epson Corporation S5U1C17M13T1 Manual (Rev.2.0) - Page 11 USB2HABM3LA 90 cm StarTech.com conversion cable Left angle mini USB extension cable, USB A male to USB Mini-B male Micro screwdriver D-67 Flat head HOZAN Note ! Parts are subject to change without notice. Seiko Epson Corporation S5U1C17M13T1 Manual (Rev.2.0)
-
Page 12: Revision History
Revision History Revision History Attachment-1 Rev. No. Date Page Category Contents Rev 2.0 2017/06/01 New establishment Seiko Epson Corporation S5U1C17M13T1 Manual (Rev.2.0) - Page 13 Phone: +49-89-14005-0 FAX: +49-89-14005-110 Keyuan South RD(Shenzhen bay), Nanshan District, Shenzhen 518054, CHINA Phone: +86-10-3299-0588 FAX: +86-10-3299-0560 EPSON TAIWAN TECHNOLOGY & TRADING LTD. 14F, No. 7, Song Ren Road, Taipei 110, TAIWAN Phone: +886-2-8786-6688 FAX: +886-2-8786-6660 EPSON SINGAPORE PTE., LTD.