Related Manuals for ABB EV3
Summary of Contents for ABB EV3
- Page 1 — ENERGY METER User Manual User Manual Document ID: 9AKK107991A1347 Revision: A 2020-12-01 1/2 1...
- Page 2 © Copyright 2020 ABB Spa. All rights reserved. Trademarks ABB Spa is a registered trademark of the ABB Group. All other brand or product names mentioned in this document may be trademarks or registered trademarks of their respective holders.
-
Page 3: Table Of Contents
2 Technical data ..........................7 Abbreviations ..........................7 Technical specifications ......................7 2.2.1 Technical Standards ....................9 3 Dimension, Assembling and Installation EV3 012-100 ............10 Assembling and dimensions ....................10 Installation ........................... 12 Protection Housing ........................13 EV3 ..............................14 4 LCD-Display ..........................15 5 User Buttons.......................... -
Page 4: General Information
For the device no servicing is required. Disposal (product end of life information) This meter was designed and built by ABB to provide many years of service and is backed by our commitment to provide high quality support. When it eventually reaches the end of its serviceable life, it should be disposed in accordance with local or national legislation. -
Page 5: Environment
This meter product is warranted against defects in material and workmanship for a period of one year from date of shipment. During the warranty period ABB will at its option, either re- pair or replace products which prove to be defective. For warranty service or repair, this prod- uct must be returned to a service facility designated by ABB. -
Page 6: Symbols
Symbols Danger through Electric Voltages The symbol indicates warnings, which may lead to personal inju- ries or death if it is ignored. Take all necessary precautions to avoid danger! Warning The symbol indicates warnings to a possible dangerous situation which may lead to personal injuries or damage to properties. Avoid dangerous situations! Attention! “Attention”... -
Page 7: Technical Data
Technical data Abbreviations Import active energy (to customer) Export active energy (from customer) European Standard Imp/kWh Quantity of pulses each kWh Liquid Crystal Display Light Emitting Diode OBIS Object Identification System Import active power Export active power Technical specifications Type Three phase direct Voltage Nominal voltage U... - Page 8 Measuring Active Energy Two Energy Directions +A/-A Meter constant LED-Output 1000 Imp/kWh Display 7 digit > 12 years Life cycle RS485- Data Interface Connector 3P meter: Three screws type Parameter 9600/19200/38400 bps, 8E1 Communication protocol Modbus RTU Power Consumption Voltage circuit <...
-
Page 9: Technical Standards
2.2.1 Technical Standards EN 50470-1: Electricity metering equipment (AC) -Part 1: General requirements, test and test conditions Metering equipment (class indexes A, B, and C); EN 50470-3: Electricity metering equipment (AC) -Part 3: Particular requirement Static me- ters for active energy (class indexes A, B, and C); EN 50022: Low voltage switchgear and control gear for industrial use;... -
Page 10: Dimension, Assembling And Installation Ev3 012-100
Dimension, Assembling and Installation EV3 012-100 Assembling and dimensions The meter constructed for assembling on DIN-rail TH 35-7.5 according to IEC 60715. 1 Housing EV3 Element Meter Hook User Buttons DIN Rail Meter cover Meter case Terminal block with cover... - Page 11 2 Housing EV3 dimension (mm) Terminal block (mm) 11 /2 1...
-
Page 12: Installation
Installation 4 Connection diagram EV3 The connection diagram printed on the housing needs to be considered connecting the me- ter to the mains power. Terminal Terminal Terminal- Terminal screw Torque M [Nm] [mm] Current In L1 6,3 x 5,6 M4 Pozidrive PZ2 1,2 Nm<... -
Page 13: Protection Housing
Warning The requirements of the net provider need to be full filled. Selective hedges have to be used according requirements of the net providers. Attention! Damage of the terminals due to high torque The specified maximum torques must not be exceeded! Ensure that the connected lines are fixed with the needed torque compliant to EN 60999 for a safe connection. - Page 14 6 EV3 Nameplate Element Function Terminal block with cover sealable terminal cover Meter number with barcode 128 User buttons Information describe in chapter 7 7 digits with additional symbols Meter type test LED 1000 Imp/kWh Technical nominal data 3 phase 4 Wire...
-
Page 15: Lcd-Display
Manufacture year LCD-Display The LCD has the following format: - LCD size: 37.5 mm × 17 mm - Digit size: 3.38 mm × 1,53 mm 7 EV3 LCD 7: LCD-Display Element Function Unit unit of the displayed value (kWh, W, V, A) -
Page 16: User Buttons
Import OBIS Code Identifier of the displayed value User Buttons 8 EV3 User buttons Element Function Switch backlight of the LCD ON Button „Up“ Scrolling the display items Enter display ALT Mode Switch backlight of the LCD ON Button „Down“... -
Page 17: Components
Analog to digital converter for the sampled voltage and current MCU: Micro Controller Unit Communication interface: RS485-Interface Data storage EV3: nonvolatile storage for energy register +A/-A and meter pa- rameter in EEPROM. Display EV3: LCD with 7 digits LED Pulse output:... -
Page 18: Functionality
Functionality Measurement The meter measures three phase active energy with accuracy class B. The meter provides registers for total import, total export and net energy. Additionally, each phase L1, L2 and L3 for import and export energy are measured. The measurement of the energy is based on the measured power according the following cal- culations: total >... -
Page 19: Status Diagram
8.2.1 Status Diagram 10 Status diagram display mode After power on the meter shows for 2s self-check status and goes on to the AUTO-Mode. With the user buttons it can be changed between the different modes. 19/2 1... -
Page 20: Auto Mode And Alt Mode
“--FF--” This status will be indicated with current display items flashing (1Hz). Backlight EV3 Backlight will be on after pressing button, it’s useful to read meter through LCD when it in dark environment. - Page 21 RS485 Interface & Registers Default Modbus settings: Baud rate = 9600 (settable) Device Address = 1 (settable) Parity = Even (not settable) Registers are listed in document 9AKK107991A9529 2 1/ 2 1...