Self-Diagnosis Code Table - Sony DCR-IP5 Service Manual

DCR-IP5/IP5E/IP7BT/IP7E
4.

SELF-DIAGNOSIS CODE TABLE

Self-diagnosis Code
Block Detailed
Function Code
C 0 4 0
C 2 1 0
C 2 2 0
C 3 1 1
C 3 1 1
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 3
C 3 1 3
C 3 1 4
C 3 1 4
C 3 1 4
C 3 1 4
C 3 2 1
C 3 2 1
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 3
C 3 2 3
C 3 2 4
C 3 2 4
C 3 2 4
C 3 2 4
E 6 1 0
E 6 1 1
Symptom/State
0 Non-standard battery is used.
0 Condensation.
0 Video head is dirty.
LOAD direction. Loading does not
0
complete within specified time
UNLOAD direction. Loading does not
1
complete within specified time
0 T reel side tape slacking when unloading.
1 Winding S reel fault when unloading.
2 T reel fault.
3 S reel fault.
1 FG fault during capstan operations.
2 Capstan reverse rotation.
0 FG fault when starting drum.
1 PG fault when starting drum.
2 FG fault during normal drum operations.
3 PG fault during normal drum operations.
LOAD direction loading motor time-
0
out.
UNLOAD direction loading motor
1
time-out.
T reel side tape slacking when
0
unloading.
1 Winding S reel fault when unloading.
2 T reel fault.
3 S reel fault.
1 FG fault during capstan operations
2 Captan reverse operations
0 FG fault when starting drum
1 PG fault when starting drum
FG fault during normal drum
2
operations
PG fault during normal drum
3
operations
Difficult to adjust focus
0
(Cannot initialize focus.)
Zoom operations fault
0
(Cannot initialize zoom lens.)
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Inspect the lens block focus MR sensor (Pin rh,rj of CN2021 of VC-
263 board) when focusing is performed using the manual focus buttons
on the menu screen, and the focus motor drive signals (Pin ea,es of
CN2021 of VC-263 board) when the focusing is not performed.
Inspect the lens block zoom MR sensor (Pin rl,t; of CN2021 of
VC-263 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive signals (Pin wl,e; of CN2021
of VC-263 board) when zooming is not performed.
— 8 —
Correction