Sharp SMD2499FS Installation Manual

Sharp SMD2499FS Installation Manual

Convection microwave drawer
Hide thumbs Also See for SMD2499FS:

Advertisement

Convection Microwave Drawer: SMD2499FS
SPECIAL WARNING
• INSTALLATION AND SERVICE MUST BE PERFORMED
BY A QUALIFIED INSTALLER.
• IMPORTANT: SAVE this installation manual FOR
LOCAL ELECTRICAL INSPECTOR'S USE.
• READ AND SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
CLEARANCES AND DIMENSIONS
For SAFETY CONSIDERATIONS do not install drawer
in any combustible cabinetry, which is not in accord
with the stated clearances and dimensions on pages
2 - 4. See Figures 1 - 7.
UNPACKING YOUR CONVECTION
MICROWAVE DRAWER
A minimum of two people are required to handle the oven. Use
the two handles located on each side of the oven to lift.
1 Remove all packing materials from inside the Convection Micro-
wave Drawer and on the Drawer door.
2 Remove the feature sticker, if there is one. Check the drawer for
any damage, such as misaligned or bent drawer, damaged drawer
seals and sealing surfaces, broken or loose drawer guides and dents
inside the cavity or on the front side of the drawer. If there is any
damage, do not operate the Convection Microwave Drawer and
contact your dealer or a SHARP AUTHORIZED SERVICER.
Sealing
Surface
INSTALLATION MANUAL
Sealing
Surface
Oven
Cavity
IMPORTANT NOTES TO THE INSTALLER
• Read all of the Installation Manual before installing the
Convection Microwave Drawer.
• Remove all packing material before connecting the electrical
supply.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
IMPORTANT NOTES TO THE CONSUMER
Keep this manual with your Operation Manual for future reference.
• As when using any oven generating heat, there are certain safety
precautions you should follow. These are listed in the Operation
Manual. Read all and follow carefully.
• Be sure your Convection Microwave Drawer is installed and
grounded properly by a qualified installer or service technician.
• This unit comes equipped with a Wi-Fi connectivity option.
In order to activate the Wi-Fi functionality, the area in which
the unit is installed requires a Wi-Fi signal. Please see the
operation manual for the minimum Wi-Fi specifications.
IMPORTANT SAFETY INSTRUCTIONS
If the information in this manual is not followed
exactly, a fire or electrical shock may result that could cause property
damage, personal injury or death.
• This Convection Microwave Drawer must be electrically
grounded in accordance with local codes.
• Make sure the wall coverings and the cabinets around the
Convection Microwave Drawer can withstand the heat
generated by the Convection Microwave Drawer.
NEVER LEAVE CHILDREN ALONE OR
UNATTENDED IN THE AREA WHERE A CONVECTION MI-
CROWAVE DRAWER IS IN USE. NEVER LEAVE THE DRAWER
OPEN WHEN THE OVEN IS UNATTENDED.
STEPPING, LEANING OR SITTING ON THE
DRAWER MAY RESULT IN SERIOUS INJURIES AND CAN
ALSO CAUSE DAMAGE TO THE CONVECTION MICROWAVE
DRAWER.
• Do not use the Convection Microwave Drawer as a storage
space. This creates a potentially hazardous situation.
• Check that the time-of-day is in the display. If not, touch STOP/
CLEAR for safety reasons and to prevent unintended use.
1
1
E

Advertisement

Table of Contents
loading

Summary of Contents for Sharp SMD2499FS

  • Page 1 Convection Microwave Drawer and • Make sure the wall coverings and the cabinets around the contact your dealer or a SHARP AUTHORIZED SERVICER. Convection Microwave Drawer can withstand the heat generated by the Convection Microwave Drawer.
  • Page 2: Clearances And Dimensions

    Power cord access hole in cabinet should be a minimum 1 " diameter hole and deburred of all sharp edges. Always allow sufficient power cord length to the IMPORTANT electrical outlet to prevent tension.
  • Page 3 24" CONVECTION MICROWAVE DRAWER STANDARD MOUNT AND MEASUREMENTS Figure 3 represents a typical standard cabinet. If installed in custom cabinets with extended countertops, take into account Move oven location downward for visibility and access to controls. See Figure 4. extended countertops Extended countertops Figure 4 Figure 3...
  • Page 4 24" CONVECTION MICROWAVE DRAWER FLUSH MOUNT AND MEASUREMENTS Prepare cabinet opening as shown in Figures 5, 6, 7 A. Suggested electrical outlet location B. 5" (127 mm) C. 4" (101.60 mm) D. 23 " (606.43 mm) E. 19 " (492.12 mm) F.
  • Page 5: Electrical Outlet

    ELECTRICAL OUTLET DRAWER INSTALLATION The electrical requirements are a 120 volt 60 Hz, AC only, 15 1. Place the Convection Microwave Drawer adjacent to the amp. or more protected electrical supply. It is recommended that wall or cabinet opening. Plug the power supply cord into the a separate circuit serving only this appliance be provided.
  • Page 6: Model And Serial Number Location

    CARE, CLEANING AND MAINTENANCE Refer to the warranty in your Operation Manual for Sharp’s toll- free service number and address. Please call or write if you have Refer to the Operation Manual for cleaning instructions.
  • Page 8 SHARP ELECTRONICS CORPORATION • 100 Paragon Drive • Montvale, New Jersey 07645 • USA T IN S EB 5 8 0 MRR0 D E c 3, 2 0 2 0...

Table of Contents