1. INPUT/OUTPUT SETTING MODE 1.1 Outline of setting procedure ⑨ ⑧ ⑫ ⑩ ⑪ A A A A C C C C D D D D PATTERN PATTERN B B B B PATTERN PATTERN F F F F E E E E △...
1.4 Examples of optional solenoid output settings 1.To change the presser foot lifter solenoid from latch type to lockstitch machine type. (SBL) L1.r2 L1.r2] will appear on the panel. L1.r2 (1) While pressing the FUNC key, press the C△ key two or more seconds. [L1.r2 L4.PL L4.PL L4.PL] with the A△...
Page 7
5.To set SOL6 signal to air wiper [L6.W3] L1.** ** ** **] will appear on the panel. (1) While pressing the FUNC key, press the C△ key two or more seconds. [L1. L6.** ** ** **] with the A△ key or the B△ key. (2) Select the item [L6.
1.7 Examples of optional output signal settings 1.To use the signal while the machine is running The default setting of the OUT0 signal is [o0.Mv]. The OUT0 signal is ON while the machine is running. (NOTE) Running condition (move/stop) signal can only be set in OUT0. 2.To use the signal for counting the number of stitches of sewing machine The default setting of the OUT1 signal is [o1.UP] (needle up signal).
Page 11
12.To use the BTSW ON signal o*.bt o*.bt] . (Turned on by BTSW signal) o*.bt Set the signal to [o*.bt When the BTSW signal is turned ON, the OUT* signal is turned ON. 13.To use the PRSW ON signal o*.Pr o*.Pr] .
1.11 Examples of optional input signal settings 1.To use the half stitch, needle UP or needle DOWN operation ★ The following is the setting procedure to set the signal in IN2. L1.** L1.**] will appear on the panel. L1.** (1) While pressing the FUNC key, press the C△...
1.12 Examples of SW input signal settings 1.Setting procedure L1.** L1.**] will appear on the panel. L1.** (1) While pressing the FUNC key, press the C△ key two or more seconds. [L1.** bt.** bt.** bt.**] with the FUNC key. (2) Select the item [bt.** (3) Select the SW input signal with the A△...
1.13 Table of default values of output signal settings When the head setting is done, the solenoid and optional signal settings will be automatically assigned as follows: ★ ★ ★ ★ The output settings indicated by crosshatching are changeable. (It is output inhibit only that can be set in the other output settings.) Single/Twin Signal B891...
1.14 Table of default values of input signal settings When the head setting is done, the input signals will be automatically assigned as follows: ★ ★ ★ ★ The input settings indicated by crosshatching are changeable. (It is output inhibit only that can be set in the other output settings.) Single/Twin signal B891...
2. COUNTER SETTING MODE 2.1 Outline of setting procedure ⑨ ⑧ ⑫ ⑩ ⑪ A A A A C C C C D D D D PATTERN PATTERN PATTERN PATTERN B B B B F F F F E E E E △...
2.3 Setting production counter ★ The production quantity can be displayed on the F-40 or F-100 panel. 2.3.1 How to set the production counter dM.** dM.**] will appear on the panel. dM.** (1) While pressing the FUNC key, press the D△ key. [dM.** dM.PC dM.PC dM.PC] with the C△...