Kenwood NX-200 Service Manual page 69

■ Frequency and Signaling
The transceiver has been adjusted for the frequencies
shown in the following table. When required, readjust them
following the adjustment procedure to obtain the frequen-
cies you want in actual operation.
• Test frequency
CH RX (MHz)
1 155.05000
2 136.05000
3 173.95000
4 155.00000
5 155.20000
6 155.40000
7~16
• Analog mode signaling
No. RX
1 None
2 None
LTR Data:
AREA=0, GOTO=12
3
HOME=12
ID=47, FREE=25
4 QT: 67.0Hz
5 QT: 151.4Hz
6 QT: 210.7Hz
7 QT: 254.1Hz
8 DQT: D023N
9 DQT: D754I
10 DTMF: 159D
11 None
2-tone:
12 A: 304.7Hz
B: 3106.0Hz
13 Single Tone: 979.9Hz
14 None
15 None
16 MSK
• NXDN mode signaling
No. RX
1 RAN1
2 None
3 RAN1
7 None
RAN: Radio Access Number
PN9: Pseudo-Random Pattern (for production only)
ADJUSTMENT /
TX (MHz)
155.10000
136.10000
173.90000
155.00000
155.20000
155.40000
- -
TX
None
100Hz Square Wave
LTR Data:
AREA=0, GOTO=12
HOME=12
ID=47, FREE=25
QT: 67.0Hz
QT: 151.4Hz
QT: 210.7Hz
QT: 254.1Hz
DQT: D023N
DQT: D754I
DTMF: 159D
DTMF Code 9
2-tone:
A: 304.7Hz
B: 3106.0Hz
Single Tone: 979.9Hz
Single Tone: 1000Hz
MSK
MSK
TX
RAN1
PN9
Maximum deviation pattern
FSW+PN9
调整
■频率和信令
已经根据下表所示的频率调整了设置。需要时，按调整步
骤重新调整，以获得实际操作时想要的频率
• 测试频率
CH 接收 (MHz)
1 155.05000
2 136.05000
3 173.95000
4 155.00000
5 155.20000
6 155.40000
7~16
• 模拟模式信令
No. 接收
1 无
2 无
LTR 数据 :
AREA=0,GOTO=12
3
HOME=12
ID=47,FREE=25
4 QT: 67.0Hz
5 QT: 151.4Hz
6 QT: 210.7Hz
7 QT: 254.1Hz
8 DQT: D023N
9 DQT: D754I
10 DTMF: 159D
11 无
2- 音 :
12 A: 304.7Hz
B: 3106.0Hz
13 单音 : 979.9Hz
14 无
15 无
16 MSK
• NXDN 模式信令
No. 接收
1 RAN1
2 无
3 RAN1
7 无
RAN: 无线接入编号
PN9: 伪随机模式 ( 仅用于生产 )
NX-200
发射 (MHz)
155.10000
136.10000
173.90000
155.00000
155.20000
155.40000
- -
发射
无
100Hz 方波
LTR 数据 :
AREA=0,GOTO=12
HOME=12
ID=47,FREE=25
QT: 67.0Hz
QT: 151.4Hz
QT: 210.7Hz
QT: 254.1Hz
DQT: D023N
DQT: D754I
DTMF: 159D
DTMF 代码 9
2- 音 :
A: 304.7Hz
B: 3106.0Hz
单音 : 979.9Hz
单音 : 1000Hz
MSK
MSK
发射
RAN1
PN9
最大频偏模式
FSW+PN9
69