Sealey SA374 Quick Manual

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. safety
Disconnect the tyre inflator from the air supply before changing accessories, servicing or performing any maintenance.
9
Keep children and unauthorised persons away from the work area.
9
Keep the gauge LCD screen and tyre inflator clean.
9
Replace damaged parts with genuine Sealey parts. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Check condition of the batteries regularly.
9
Check tyre pressures when they are cold.
9
Do not direct the tyre inflator outlet at yourself or others including animals.
8
Do not carry the tyre inflator by the hose, or tug the hose from the air supply.
8
Do not use the tyre inflator for a task which it is not designed to perform.
8
Do not operate the tyre inflator when you are tired or under the influence of intoxicating medicines, drugs or alcohol.
8
Do not operate the tyre inflator if parts are missing or the LCD is damaged, this could be dangerous.
8
Do not drop or bump the tyre inflator.
8
Do not get the tyre inflator wet.
8
Do not operate near appliances with strong magnetic fields, corrosive gasses or corrosive liquids.
8
2. introDuCtion
2.1. sa374
die-cast aluminium body with large rubber bumper, backlit LCD digital display and battery level indicator. Auto power off after eight seconds
and auto power on once pressure is sensed, or air inflation starts. 0.5m Flexible hose fitted with 240mm push-on air connector. Supplied with
a serial numbered calibration certificate.
2.2. sa375
die cast aluminium body with large rubber bumper, backlit LCD digital display and battery level indicator. Auto power off after eight seconds
and auto power on once pressure is sensed, or air inflation starts. 2.7m Flexible hose fitted with clip-on air connector. Supplied with a serial
numbered calibration certificate.
3. sPeCifiCation
model no:.............................................................................sa374 ....................................................................... sa375
Accuracy: ................................................................. 25-75psi ±2psi . .......................................................... 25-75psi ±2psi
Battery Run Time: ...................................................................80hrs . ........................................................................ 80hrs
Battery: .............................................................. 2 x AAA (supplied) . .................................................... 2 x AAA (supplied)
Inlet Size: ........................................................................... 1/4"BSP . ....................................................................1/4"BSP
Maximum Air Supply: ..............................................13.8bar(200psi) . ........................................................ 13.8bar(200psi)
nett Weight: ..........................................................................1.15kg . ...................................................................... 1.15kg
Pressure Units: ............................................................bar, psi, kPa . ............................................................. bar, psi, kPa
Range: ................................................................ 0-12bar(0-174psi) . .....................................................0-12bar(0-174psi)
4. oPeration
4.1. to reaD Pressure
4.1.1. Place hold-on chuck squarely and firmly onto tyre valve, before each pressure reading fully depress lever and release.
4.1.2. Check pressure gauge, the digital display will activate once the tyre pressure is sensed. If no pressure is sensed the display will not
turn on, please press trigger to add air into tyre, before reading pressure.
4.2. to inflate
4.2.1. Place chuck squarely and firmly onto the valve. Fully depress lever for an appropriate period then release lever to display
pressure. Check pressure gauge and repeat procedure until correct pressure level is achieved.
4.3. to Deflate
4.3.1. Depress lever half way (until air can be heard escaping) for an appropriate period, fully depress lever momentarily then release to
display new pressure. Check pressure gauge and repeat procedure until correct pressure level is achieved.
© Jack Sealey Limited
Digital tyre inflator 0.5m Hose witH twin
PusH-on CHuCk, Digital tyre inflator
2.7m Hose witH CliP-on ConneCtor
sa374, sa375
Model no:
Original Language Version SA374 SA375 Issue 1 10/06/19