Epson DP-110 Installation Manual

Installation Manual
Safety Precautions
This documents uses the two headings shown below to call attention to potential hazards. Failure to observe the
information provided alongside these headings may lead to injury or damage to your system. Be sure that you
understand the meaning of each heading before you proceed.
Indicates a potentially lethal hazard. Failure to observe a WARNING may result in
WARNING
severe injury or death.
Failure to observe a CAUTION may result in personal injury, or in damage to
CAUTION
equipment or other property.
❏
Shut down your equipment immediately if it produces smoke, a strange odor,
WARNING
or unusual noise. Continued use may lead to fire.
Immediately turn the power off and consult your dealer or a SEIKO EPSON
service center for advice.
❏
Never attempt to repair this product yourself. Improper repair work can be
dangerous.
Tampering with this product may result in injury, fire, or electric shock.
❏
Never disassemble or modify this product.
Tampering with this product may result in injury, fire, or electric shock.
❏
Be sure to use the specified power source.
Connection to an improper power source may result in fire or electric shock.
❏
Do not allow foreign matter to fall into the equipment.
Penetration of foreign objects may result in fire or electric shock.
❏
If water or other liquid spills into this equipment, immediately turn the power
off and consult your dealer or a SEIKO EPSON service center for advice.
Continued usage may result in fire or electric shock.
❏
Be sure to set this product on a firm, stable, horizontal surface.
CAUTION
The product may break or cause injury if it falls.
❏
Do not use in locations subject to high humidity or dust levels.
Excessive humidity and dust may cause equipment damage, fire, or electric
shock.
❏
Do not place heavy objects on top of this product. Never stand or lean on this
product.
Equipment may fall or collapse, causing breakage and possible injury.
Unpacking
Please confirm that this package contains these items:
❏ DM-D stand
❏ Extension cable for
power supply
Stand Unit for DM Customer Display
❏ Base plate
❏ RS-232 connector
installation screw (mm type)
Connecting to the DM Customer Display
Please refer to the DM-D110 User's Manual for the procedure to connect this unit to the DM-D110.
EMC and Safety Standards Applied
Product Name: DM Stand
Type Name: M167A
The following standards are applied only to the DM stand that is so labeled. (EMC is tested using the EPSON
PS-180 power supply.)
Europe: CE Marking
Safety: EN60950-1
North America: EMI: FCC/ICES-003 Class A
Safety: UL 1950/CSA C22.2 No.950
Japan: EMC: VCCI Class A
Oceania: EMC: AS/NZS CISPR22 Class A
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
The connection of non-shielded interface cable to this DM stand will invalidate the EMC standards of this
device.
You are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could
void your authority to operate the equipment.
CE Marking
The display conforms to the following Directives and Norms:
Directive 2004/108/EC EN 55022 Class A
EN 55024
IEC 61000-4-2
IEC 61000-4-5
FCC Compliance Statement for American Users
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
For Canadian Users
This Class A digital apparatus complies with canadian ICES-003.
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson
Corporation. No patent liability is assumed with respect to the use of the information contained herein. While every
precaution has been taken in the preparation of this guide, Seiko Epson Corporation assumes no responsibility for errors
or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this
product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly
comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any
consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko
Epson Corporation.
EPSON is a registered trademark of Seiko Epson Corporation in Japan and other countries/regions.
NOTICE: The contents of this manual are subject to change without notice.
IEC 61000-4-3 IEC 61000-4-4
IEC 61000-4-6 IEC 61000-4-11