Mitsubishi Electric M Series Manual page 57

●Connect CN591 with Switch1 and Switch2 as shown in figure above.
9. Remote Control
●Connect the supplied lead wires (3-core)
the interface unit.
Connecting the SYSTEM CONTROL Interface
●Connect the supplied lead wires (3-core)
in the interface as shown in the figure on the right side.
1. CONTROLS
You can turn room air conditioner on/off, prohibit/allow manual operations, or input of heating/cooling
●Wiring length from the interface to the Switch1 and Switch2 should be less than 50m [164ft].
with the ON/OFF switch.
●Procure and wire locally the remote control part including the switches.
Interface unit
Indoor unit
●For each connection pattern, refer to "Setting when using remote control."
1-4. System Control Interface [MAC-333IF-E], cont.
*When using a Card key/Coin timer, make connections shown in the figure to the right.
SW500
Setting when using remote control (Select one between No.1 through 5 and set.)
*Set No.1, No.6, and No.7 when using the card key/coin timer.
SW502
No. F u n t c o i n s S
SW500
ON
ON/OFF
●Connect CN591 with Switch1 and Switch2 as shown in figure above.
Manual operation
1 1 2 3
●Connect the supplied lead wires (3-core)
prohibited/allowed
SW502
the interface unit.
(Level Contact)
ON
●Connect the supplied lead wires (3-core)
in the interface as shown in the figure on the right side.
1 2 3
●Wiring length from the interface to the Switch1 and Switch2 should be less than 50m [164ft].
SW500
●Procure and wire locally the remote control part including the switches.
ON
ON/OFF
●For each connection pattern, refer to "Setting when using remote control."
Manual operation
*When using a Card key/Coin timer, make connections shown in the figure to the right. 1 2 3
2
prohibited/allowed SW502
ON
(Pulse Contact)
Setting when using remote control (Select one between No.1 through 5 and set.)
1 2 3
*Set No.1, No.6, and No.7 when using the card key/coin timer.
SW500
No. F u n t c o i n s S
ON
ON/OFF
SW500
Remote operation/
3 1 2 3
ON SW502
Manual operation
ON/OFF
ON
(Level Contact)
Manual operation
1 1 2 3
prohibited/allowed
SW502
1 2 3
(Level Contact)
ON
SW500
ON
1 2 3
SW500
ON, OFF
1 2 3
4
ON
SW502
(Pulse Contact)
ON/OFF
ON
Manual operation
1 2 3
2
prohibited/allowed SW502
1 2 3
ON
(Pulse Contact)
SW500
1 2 3
ON
Heating/cooling
SW500
5 input (Level 1 2 3
ON
ON/OFF
SW502
Contact)
Remote operation/
ON
3
1 2 3
Manual operation SW502
ON
(Level Contact) 1 2 3
Setting operation (Valid only for No.1 and No.2. The following 2 functions can be used at the same time.)
1 2 3
SW500
No. F u n t c o i n s S
ON
ON, OFF
SW502
1 2 3
4
SW502
(Pulse Contact)
Behavior when
ON
6 operation is
ON
prohibited.
1 2 3
1 2 3
SW500
SW502
ON
Behavior when
Heating/cooling
prohibition of
7 ON
5 input (Level 1 2 3
operation is
SW502
Contact)
canceled.
ON 1 2 3
1 2 3
Setting operation (Valid only for No.1 and No.2. The following 2 functions can be used at the same time.)
No. F u n t c o i n s S
SW502
Behavior when
6 operation is
ON
prohibited.
1 2 3
SW502
Behavior when
prohibition of
7 ON
operation is
canceled.
1 2 3
Due to continuing improvement, above specification may be subject to change without notice.
© 2016 Mitsubishi Electric US, Inc.
to the connector CN591 on
to the connecting cable
CN591
3 2 1
Switch1
CN560
W N . o H o w o t u s e
Switch2
Switch1:
Brown
1
ON/OFF
Red
2
4 5 6 7 8
Switch2:
to the connector CN591 on
Orange
3
Manual operation
CN591
to the connecting cable prohibited/allowed
4 5 6 7 8
Switch1:
Brown
1
ON/OFF
Red
4 5 6 7 8
2
Switch2:
Orange
3
Manual operation
prohibited/allowed
CN591
4 5 6 7 8
W N . o H o w o t u s e
Switch1:
Brown
1 ON/OFF
Red
2
4 5 6 7 8 Switch1: Switch2:
Brown
Orange
1
3
ON/OFF Remote operation/
Red
2
CN591 Manual operation
4 5 6 7 8
Switch2:
Orange
3
4 5 6 7 8
Manual operation
CN591
prohibited/allowed
Brown
4 5 6 7 8
Switch1:
1
Red ON
2
4 5 6 7 8
Switch1:
Orange
Brown Switch2:
3
1
ON/OFF
OFF
Red
CN591
4 5 6 7 8
2
Switch2:
Orange
4 5 6 7 8
3
Manual operation
prohibited/allowed
CN591
4 5 6 7 8
Brown
Switch1:
1
Red
ON/OFF
Switch1:
2
4 5 6 7 8
Brown
1 Orange ON/OFF
Switch2:
3
Red
2 Heating/Cooling
Switch2:
4 5 6 7 8
CN591
Orange
3
Remote operation/
4 5 6 7 8
CN591 Manual operation
4 5 6 7 8
W N . o H o w o t u s e
Brown
Switch1:
1
Red ON
2
4 5 6 7 8
Operational status of room
Orange
ON Switch2:
3
air conditioner when
OFF
CN591
manual operation is
prohibited can be set.
4 5 6 7 8
4 5 6 7 8
OFF
Operational status of room
Brown
Switch1:
ON 1
air conditioner when
Red
ON/OFF
prohibition of manual
2
4 5 6 7 8
Orange
Switch2:
operation is canceled can
3
4 5 6 7 8
Heating/Cooling
be set.
OFF
CN591
4 5 6 7 8
W N . o H o w o t u s e
Operational status of room
ON
air conditioner when
manual operation is
prohibited can be set.
4 5 6 7 8
OFF
Operational status of room
ON
air conditioner when
prohibition of manual
operation is canceled can
4 5 6 7 8
be set.
OFF
Indoor unit
Switch1, Switch2
(Usable at DC12V, 0.5 to 2.0mA)
• Unit is turned on when Switch1 has a short-circuit, and off when open.
Card key coin timer connection
(Regardless of the Switch1 operation condition, the latest operation is prioritized.)
• When Switch2 has a short-circuit, manual operation is prohibited,* and when open, manual operation is allowed.
Indoor unit
• When SW502-4 is turned on, the opening and short-circuiting of
Switch1 and Switch2 result in their operating in the opposite manner.
*When manual operation is prohibited, ON/OFF operation of the wireless
remote controller, the MA remote controller, and the ME remote controller is
prohibited. (Operation from Switch1 and M-NET system controller is possible.)
• Every time Switch1 is pressed, ON/OFF is switched over.
(Regardless of the Switch1 operation condition, the latest operation is prioritized.)
• Every time Switch2 is pressed, the manual operation prohibited*/the
manual operation allowed is switched over.
*When the manual operation is prohibited, ON/OFF operation of the wireless
remote controller, the MA remote controller, and the ME remote controller is
prohibited. (Operation from Switch1 and M-NET system controller is possible.)
• Unit is turned on when Switch1 has a short-circuit, and off when open.
• When Switch2 has a short-circuit, only Switch1 is enabled (remote
operation)*, when open, only Switch1 is disabled (manual operation).
• Unit is turned on when Switch1 has a short-circuit, and off when open.
• When SW502-4 is turned on, the opening and short-circuiting of
(Regardless of the Switch1 operation condition, the latest operation is prioritized.)
Switch1 and Switch2 result in their operating in the opposite manner.
• When Switch2 has a short-circuit, manual operation is prohibited,* and when open, manual operation is allowed.
*In remote operation, ON/OFF operation from the wireless remote
• When SW502-4 is turned on, the opening and short-circuiting of
controller, the MA remote controller, the ME remote controller, and the
Switch1 and Switch2 result in their operating in the opposite manner.
M-NET system controller cannot be used.
*When manual operation is prohibited, ON/OFF operation of the wireless
remote controller, the MA remote controller, and the ME remote controller is
• Unit is turned on no matter how many times Switch1 is pressed.
prohibited. (Operation from Switch1 and M-NET system controller is possible.)
• Unit is turned off no matter how many times Switch2 is pressed.
And regardless of the Switch1, Switch2 operation condition, the
• Every time Switch1 is pressed, ON/OFF is switched over.
latest operation is prioritized.
(Regardless of the Switch1 operation condition, the latest operation is prioritized.)
• ON/OFF operation from the wireless remote controller, the ME
• Every time Switch2 is pressed, the manual operation prohibited*/the
remote controller, the MA remote controller, and the M-NET system
manual operation allowed is switched over.
controller is enabled.
*When the manual operation is prohibited, ON/OFF operation of the wireless
remote controller, the MA remote controller, and the ME remote controller is
• Unit is turned on when Switch1 has a short circuit, and off when open.
prohibited. (Operation from Switch1 and M-NET system controller is possible.)
• Heating runs when Switch2 has a short circuit, and cooling runs
when open.
• Unit is turned on when Switch1 has a short-circuit, and off when open.
• When SW502-4 is turned on, the opening and short-circuiting of
• When Switch2 has a short-circuit, only Switch1 is enabled (remote
Switch1 and Switch2 result in their operating in the opposite manner.
operation)*, when open, only Switch1 is disabled (manual operation).
* As for ON/OFF operation and heating/cooling operation from
• When SW502-4 is turned on, the opening and short-circuiting of
the wireless remote controller, MA remote controller, ME remote
Switch1 and Switch2 result in their operating in the opposite manner.
controller, system controller, Switch1, and Switch2, the latest
*In remote operation, ON/OFF operation from the wireless remote
operation is prioritized.
controller, the MA remote controller, the ME remote controller, and the
M-NET system controller cannot be used.
• Unit is turned on no matter how many times Switch1 is pressed.
• Unit is turned off no matter how many times Switch2 is pressed.
And regardless of the Switch1, Switch2 operation condition, the
SW502-5: OFF
latest operation is prioritized.
• When manual operation is prohibited by Switch2, operational status
• ON/OFF operation from the wireless remote controller, the ME
is maintained as that before manual operation is prohibited.
remote controller, the MA remote controller, and the M-NET system
SW502-5: ON
controller is enabled.
• When manual operation is prohibited by Switch2, the room air
conditioner turns off.
• Unit is turned on when Switch1 has a short circuit, and off when open.
• Heating runs when Switch2 has a short circuit, and cooling runs
SW502-6: OFF
when open.
• When prohibition of manual operation is canceled by Switch2,
• When SW502-4 is turned on, the opening and short-circuiting of
operational status is maintained as that before cancelation.
Switch1 and Switch2 result in their operating in the opposite manner.
SW502-6: ON
* As for ON/OFF operation and heating/cooling operation from
• When prohibition of manual operation is canceled by Switch2, the
the wireless remote controller, MA remote controller, ME remote
room air conditioner turns on.
controller, system controller, Switch1, and Switch2, the latest
operation is prioritized.
SW502-5: OFF
• When manual operation is prohibited by Switch2, operational status
is maintained as that before manual operation is prohibited.
SW502-5: ON
• When manual operation is prohibited by Switch2, the room air
conditioner turns off.
SW502-6: OFF
• When prohibition of manual operation is canceled by Switch2,
operational status is maintained as that before cancelation.
SW502-6: ON
• When prohibition of manual operation is canceled by Switch2, the
room air conditioner turns on.
M-Series - Controls (December 2016)
Interface unit
CN591
Insulate
3 2 1
SW500
Signal cable
CN560
SW502
(Card key/coin timer)
Connect in the interface
unit
Cable tie
Lead wires
O p r e t a n i g d e a t s l i
Interface unit
CN591
Insulate
3 2 1
SW500
CN560
SW502
(Card key/coin timer)
O p r e t a n i g d e a t s l i
O p r e t a n i g d e a t s l i
O p r e t a n i g d e a t s l i
Switch2
Switch2
57