Control Elements; Terminal Description - ABB Video kit Manual

4 A B B - W E L C O M E V I D E O K I T
Mini Outdoor Station terminal description
7
6
5
4
3
2
1
13 12

Terminal description

1
3 4
5
2
6
10
7
10
No. Description
1 Connector for device software update
2 Rotary switch to set the address of outdoor station (1-9)
3 Set feedback tone of pushbutton ON/OFF
4 Set general call to all indoor stations in one family: ON/OFF
11 If GC=ON, press button 1/button 2, all IS ring
10
5 Configurate round pushbutton
3 -> OFF; 4 -> OFF = Call IS 001
9
8
6 Set the video mode PAL/NTSC
OFF = PAL video mode
ON = NTSC video mode
Set default lock
7
OFF = set (Lock-GND) as default lock
ON = set (COM-NC-NO) as default lock
*Default lock is controlled by "unlock" button on IS
8 Plug-in clamps (a, b) for bus connection
9 Plug-in clamps (Exit-GND) for exit button
10 Plug-in clamps (Lock-GND) for door opener
11 Plug-in clamps (COM-NC-NO) for floating output, door opener
12 Rotary switch to adjust default door lock release time, 1-10s
13 Rotary switch to adjust loudspeaker volume
No. Description
1 Default outdoor station address
Adjust the jumper connector to set the address of the default
outdoor station (1-9)
2 Indoor station hundreds digit
Adjust the jumper connector to set the hundreds digit of indoor
station among "X200", "X100" and "0"
3 No function
8
9
4 Primary/Secondary indoor station
Only one indoor station in each apartment can be set as "Primary"
(ON=Primary).
Terminal resistor
5
In video installations or mixed audio and video installations, the
switch must be set as 'RC on' on the last device of the line (ON=RC
on)
6 Indoor station tens digit
Adjust the jumper connector to set the tens digit of indoor station
(0-9)
7 Indoor station units digit
Adjust the jumper connector to set the units digit of indoor station
(0-9)
8 a1, b1 = bus connector
9 a potential free contact, such as a doorbell pushbutton
10 Only for factory use
M A N U A L

Control elements

No. Description
1 7" colour display
2 Call button
• In standby status, press to access the "Intercom" screen
• During a call request, press to accept the call
• During communication, press to terminate the call
1 • During surveillance, press to activate the manual call
3 Unlock button
• In standby status, press to release the default lock of default out-
door station. Long press 3 seconds to enable/disable the "Auto
8
unlock" function on the primary indoor station
• During a call request or communication, press to release the
9
2 3 4 5 6 7
default lock of the outdoor station which is calling
• During surveillance, press to release the default lock of the out-
door station which is under surveillance
4 Program button
In standby status, press to release the 2nd lock of the default
outdoor station by default. If multiple functions are set to the pro-
gram button, press to access the "Program button" screen
Mute button
5
• In standby status, press to activate/mute the ringtone
• In standby status, long press to mute the ringtone of all indoor
stations in the same apartment
• During a call request, press to activate/mute the ringtone and
the call will be terminated after 5 s
• During communication, press to activate/mute the microphone
6 Surveillance button
• In standby status, press to monitor the default outdoor station
• During a call request, if "One on" mode is used on the (mini)
system controller, only the primary indoor station can show the
image, for the secondary indoor station this button needs to be
pressed to obtain the image
• During communication, long press to take a snapshot
• During surveillance, press to switch to the next video stream or
terminate the surveillance
7 Setting button
• In standby status, press to enter the system settings
• During communication or surveillance, press to set the volume,
colour, contrast and brightness
8 Microphone
9 Speaker
5