Sealey PW1850 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
protection
instructions
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GENERAL SAFETY
WARNING! Water and electricity are dangerous partners. Be extremely cautious and ALWAYS be aware that this device uses an
‰
electric motor. Always plug into a RCD (See electrical safety above). Unplug from mains before changing accessories or servicing.
The appliance can be used for washing surfaces outdoors, whenever pressurised water is required to remove dirt.
9
With special optional accessories, it can be used for foaming, and for washing with a rotary brush for application to the gun.
9
This appliance's performance and user friendliness make it suitable for NON PROFESSIONAL use.
9
This appliance is for outdoor use only.
9
Ensure you comply with all local water supply regulations. Power washers may only be connected to mains water supply if a check
9
valve is installed in the supply hose, or at the tap outlet.
The supply hose must be reinforced, and have an internal diameter of 1/2". The water supply must be at least equal to the cleaner
9
capacity. The water temperature must NOT exceed 122°F (50°C). The water supply pressure must NOT exceed 6 bar (90psi).
Always be aware of the hazards that may occur during use. Study all applications and limitations of the washer before use.
9
Use where air can freely circulate around the washer to avoid the machine overheating.
9
DO NOT obstruct ventilation grilles during operation.
8
Position the washer as near to the water supply as possible.
9
WARNING: Always disconnect the electricity and water supplies on completion of every job.
‰
WARNING! DO NOT use the washer if any part of the unit, gun, nozzle, detergent tank, hose or cables is damaged. Replace or
‰
repair using genuine parts only. Unauthorised parts may be dangerous and will invalidate your warranty. Always check connections
are correctly secured and not cracked or damaged in any way before using the machine.
WARNING: This appliance has been designed for use with the detergent provided or the detergent specified by the manufacturer,
‰
such as a neutral shampoo based on biodegradable anionic surface active detergents. The use of other detergents or chemicals
may put the appliance's safety at risk.
WARNING! Ensure all persons and animals keep at a minimum distance of 15 m from the washer when in use. All persons within
‰
15 m shall wear appropriate P.P.E.
© Jack Sealey Limited
130BAR PRESSURE WASHER WITH TSS &
ROTABLAST® NOZZLE 230V
MODEL NO:
Wear protective Wear safety
footwear
gloves
Original Language Version
PW1850
Wear protective Wear ear
protection
clothing
DO NOT DO NOT direct jet
against yourself,
drink water
other persons,
from pressure
animals, electrical
washer
equipment or the
machine itself
Recommended fuse rating
13 Amp
PW1850 Issue 2 (2) 10/02/21