Panasonic FZ-10 Series Instruction Manual page 3

5 SPECIFICATIONS
Type NPN output
Item Model No. FZ-11
Applicable fibers FD-L51 (Note 1), FD-L52, FD-L53, FD-L54
Opaque or translucent object larger than the spot diameter of the
Sensing object
applicable fiber
Supply voltage 12 to 24V DC 10% Ripple P-P 10% or less
Current consumption
NPN open-collector transistor
Maximum sink current: 100mA
Applied voltage: 30V DC or less
(between output and 0V)
Output
Residual voltage:
1V or less (at 100mA sink current)
0.4V or less (at 16mA sink current)
Output operation Switchable either Coincident-ON or Incoincident-ON
Short-circuit protection
Response time 1ms or less (3ms or less when auto-teaching has been engaged)
Tolerance Adjustable in 16 grades with the tolerance adjuster
-10 to +55
Ambient temperature
Storage: -20 to +70
Ambient humidity
Emitting element Red LED Green LED Blue LED (modulated)
Material Enclosure: ABS, Case cover: Polycarbonate, Fiber lock lever: PPS
Cable
Weight
Accessories MS-DIN-3 (Amplifier mounting bracket): 1 pc., Adjusting screwdriver: 1 pc.
Notes: 1) Since fiber FD-L51 (standard type) is easily affected by specular reflection,
it is possible that teaching may not be properly done or sensing may be un-
stable if objects of high reflectivity (mirror, plated objects, copper foil, etc.)
are sensed. When such objects are to be sensed, please use FD-L52 (high
precision type) or FD-L53 (extremely small spot type) and make sure that
the projected optical beam is perpendicular to the object surface.
2) The amplifier should be used under the ambient temperature of +15 to +35
when the tolerance adjuster is set from the 1st grade of the 4th grade, which
provide fine color resolution.
6 CAUTIONS
This product has been developed / produced for industrial use only.
Make sure that the power supply is off while wiring.
Take care that wrong wiring will damage the sensor.
Verify that the supply voltage variation is within the rating.
If power is supplied from a commercial switching regulator, ensure that
the frame ground (F.G.) terminal of the power supply is connected to an
actual ground.
In case noise generating equipment (switching regulator, inverter motor,
etc.) is used in the vicinity of this product, connect the frame ground
(F.G.) terminal of the equipment to an actual ground.
Do not run the wires together with high-voltage lines or power lines or
put them in the same raceway. This can cause malfunction due to
induction.
Do not use during the initial transient time (0.5 sec.) after the power
supply is switched on.
Take care that the sensor is not directly exposed to fluorescent lamp
from a rapid-starter lamp, a high frequency lighting device or sunlight
etc., as it may affect the sensing performance.
Extension up to total 100m, or less, is possible with 0.3mm
cable. However, in order to reduce noise, make the wiring as short as
possible.
Make sure that stress by forcible bend or pulling is not applied to the
sensor cable joint.
This sensor is suitable for indoor use only.
Do not use this sensor in places having excessive vapor, dust, etc., or
where it may come in contact with corrosive gas, etc.
Take care that the sensor does not come in contact with water, oil,
grease, organic solvents, such as, thinner etc., strong acid or alkaline.
After the settings, make sure to fit the case cover on the amplifier
before use. Do not move or bend the fiber cable. If so, the operation
may become unstable.
Periodical teaching should be done to maintain stable sensing
conditions.
7 INTENDED PRODUCTS FOR CE MARKING
The models listed under ' 5
CE Marking.
As for all other models, please contact our office.
SEN TRONIC
AG
PNP output
FZ-11P
45mA or less
PNP open-collector transistor
Maximum source current: 100mA
Applied voltage: 30V DC or less
(between output and +V)
Residual voltage:
1V or less (at 100mA source current)
0.4V or less (at 16mA source current)
Incorporated
(No dew condensation or icing allowed) (Note 2)
35 to 85% RH, Storage: 35 to 85% RH
2
0.2mm 3-core cabtyre cable, 2m long
85g approx.
SPECIFICATIONS' come with
Rugghölzli 2
CH - 5453 Busslingen
Produkte, Support und Service
2
, or more,
Tel. +41 (0)56 222 38 18
Fax +41 (0)56 222 10 12
mailbox@sentronic.com
www.sentronic.com