Table of Contents
Advertisement
Parts and their functions
Front panel
DVCPRO 50
ON
POWER
2
X
DVCPRO
DV
SUPER REC INH
TCG
MODE
REMOTE
OFF
ON
ON
INT
TAPE
OFF
OFF
EXT
EE
PREVIEW/
METER
INPUT SELECT
AUTO EDIT
REVIEW
FULL/FINE
VIDEO
AUDIO
HEADPHONES
AUDIO MIX
AUDIO MON SEL
1&2
3&4
CH2/4 REC CH1/3
MIX
L
R
CH 1
CH 2
CH 3
CH 4
CH1/3
REC
UNITY
PULL
CH1/3 CH2/4 REC CH2/4
PB
VAR
AUDIO VOL SEL
ENC
VIDEO
CHROMA
SET UP
CONTROL
LEVEL
LEVEL
BLK
REMOTE
PRESET
PRESET
PRESET
LOCAL
MANUAL
MANUAL
MANUAL
\
] ^ _ `
ENC CONTROL switch
\
REMOTE:
Set to this position to adjust the video output
signals using a device which has been connected
to the 9-pin REMOTE, RS-232C or PARALLEL
connector.
LOCAL:
Set to this position to adjust the video output
signals using the unit's controls (], ^, _, `).
VIDEO LEVEL control and switch
]
These are used to adjust the video output level.
When the ENC CONTROL switch
LOCAL and the VIDEO LEVEL switch is set to
MANUAL, the video output level can be adjusted
using the VIDEO LEVEL control.
The maximum adjustment range is ±3 dB.
When the VIDEO LEVEL switch is set to PRESET,
the video output level is fixed at 0 dB.
^
CHROMA LEVEL control and switch
These are used to adjust the chroma level.
When the ENC CONTROL switch
LOCAL and the CHROMA LEVEL switch is set to
MANUAL, the chroma level can be adjusted using
the CHROMA LEVEL control.
The maximum adjustment range is ±3 dB.
When the CHROMA LEVEL switch is set to
PRESET, the chroma level is fixed at 0 dB.
14 (E)
(continued)
EJECT
XL/L/M-cassette
SHTL
SLOW
COUNTER
ASSEM
VIDEO
CUE
TC
SEARCH
PUSH
INSERT
JOG
RESET
CH 1
CH 2
CH 3
CH 4
PF 1
PF 2
PF 3
PF 4
STAND BY
PLAYER RECORDER
SET
TC PRESET
MENU
PF
EDIT
PLAY
REC
PREROLL
A IN
A OUT
REW
STOP
FF
SHIFT
IN
SET
OUT
HUE
TC
CHROMA PH
DIAG
PRESET
REGEN
REC RUN
PRESET
FREE RUN
MANUAL
a
b
is set to
\
is set to
\
SET UP (BLK) control and switch
_
These are used to adjust the setup (black) level.
When the ENC CONTROL switch
LOCAL and the SET UP switch is set to MANUAL,
the setup level can be adjusted using the SET UP
control.
The maximum adjustment range is ±14 IRE
PULL
(100 mV).
When the SET UP switch is set to PRESET, the
setup (black) level is fixed at 0 IRE (0 mV).
`
HUE (CHROMA PH) control and switch
These are used to adjust the hue (chroma phase).
When the ENC CONTROL switch
LOCAL and the HUE switch is set to MANUAL, the
hue can be adjusted using the HUE control.
The maximum adjustment range is ±30 degrees.
When the HUE switch is set to PRESET, the hue
(chroma phase) is fixed at 0 degree.
a TC (REGEN/PRESET) switch
REGEN:
The internal time code generator is synchronized
with the time code which the time code reader
has read from the tape.
The signal that is to be used for regeneration is
selected using setup menu No. 503 (TCG
REGEN).
PRESET:
The time code generator can be preset on the
operation panel or by remote control.
b TC (REC RUN/FREE RUN) switch
This sets the operation mode which is to make the
internal time code generator advance.
REC RUN:
The internal time code generator is advanced
during recording.
The time code advances all the time when the TC
(REGEN/PRESET) switch a is at the REGEN
position.
FREE RUN:
When the power is on, the internal time code
generator is advanced regardless of the operation
mode.
\
is set to
is set to
\
Advertisement
Table of Contents
