Table of Contents
Advertisement
D Press / to highlight one of the following options.
Brightness
Increase the value to brighten the picture or vice
versa. Choose zero (0) for average setting.
Contrast
Increase the value to sharpen the picture or vice
versa. Choose zero (0) to balance the contrast.
Tint
Increase the value to darken the picture or vice
versa. Choose zero (0) for average setting.
Color
Increase the value to enhance the color in your
picture or vice versa. Choose zero (0) to balance the
color.
E Press / to adjust the setting that best suits
your personal preference.
F Repeat steps D~ E for adjusting other color fea-
tures.
G Press OK to confirm.
Using the Audio setup menu
A Press SETUP on the remote control.
The system setup menu appears.
B Press / to select { Audio }, then press .
C Press / to select an item, then press to
access.
Example: { Night Mode }
The options for the selected item appears.
If the selection in the menu is greyed out, that
means the feature is not available or not possible to
change at the current state.
D Use / to select a setting and press OK to con-
firm.
Example: { On }
The setting is selected and setup is completed.
E To exit, press SETUP.
Digital Output
Select this if you connect to a multichannel decoder/
receiver.
A In 'Audio', press / to select { Digital Output },
then press .
{ All }
Select this if the connected device has a built-in
multichannel decoder that supports one of the multi-
channel audio format (Dolby Digital, DTS).
{ PCM }
Select this if the connected device is not capable of
decoding multichannel audio. The DVD player will
convert the Dolby Digital signal to PCM (Pulse Code
Modulation).
Helpful hint: Press to go back to previous menu item.
Press SETUP to exit the menu item.
DVD Menu Options (continued)
{ Off }
To deactivate the digital audio output. For example, if
you use the AUDIO OUT jacks to connect to a TV or
stereo system.
B Use / to select a setting and press OK to con-
firm.
Tip:
-If { Digital Output } is set to { All }, all audio settings
except MUTE are invalid.
-When playing MPEG , MP3 and set Digital Output to
{ALL}, the player will output PCM signals.
Night Mode
This mode optimises playback of sound at low
volume. High volume outputs will be softened and
low volume outputs are brought upward to an audible
level.
A In 'Audio', press / to select { Night Mode }, then
press .
{ On }
Select this to set low volume output. This feature
is only available for movie discs with Dolby Digital
mode.
{ Off }
Turns off night mode feature. Select this to enjoy the
surround sound with its full dynamic range.
B Use / to select a setting and press OK to con-
firm.
Down Sampling
You can enable and disable the digital signal for bet-
ter sound output quality.
A In 'Audio', press / to select { Down Sampling },
then press .
{ Off }
If your amplifier / decoder is compatible with 96 kHz
PCM, select "Off". Sound is sampled at 96 kHz.
{ On }
If your amplifier / decoder is NOT compatible with 96
kHz PCM, select "On". Sound recorded at 96 kHz is
down sampled to 48 kHz.
B Use / to select a setting and press OK to
confirm.
Tip:
- When playing back disc with copyright protection,
the sound will be down sampled to 48 kHz even
when you select Down Sampling off.
3D
To obtain expansive virtual surround sound effects
from two speakers, select 3D On, this enhancement
sounds only output from the Analog Audio out (L/R)
jacks of the DVD player
A In 'Audio', press / to select { 3D }, then press .
You can set to { Off } and { On }
B Use / to select a setting and press OK to
confirm.
Tip:
- Only effective in playback of a DVD video disc with
Dolby Digital 5.1 bitstream.
Hide quick links:
Advertisement
Table of Contents
