Husqvarna 520iHD60 Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 520iHD60
  6. Operator's manual

Husqvarna 520iHD60 Operator's Manual

Hide thumbs Also See for 520iHD60:
Table of Contents

Advertisement

Quick Links

520iHD60, 520iHD70
EN
Operator's manual
2-17

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 520iHD60

Summary of Contents for Husqvarna 520iHD60

  • Page 1 520iHD60, 520iHD70 Operator's manual 2-17...

  • Page 2: Table Of Contents

    Maintenance..............12 Introduction Product description Intended use Husqvarna 520iHD60, 520iHD70 is a battery hedge Use the product to cut branches and twigs. Do not use trimmer with an electrical motor. the product for other tasks. Work is constantly in progress to increase your safety and efficiency during operation.
  • Page 3 11. Battery charger emission of the product is specified in the Technical data chapter and on the label. 12. Cord 13. Battery indicator button 14. Battery status 15. Warning indicator 16. SavE button Lock for handle adjustment. 17. Start and stop button 18.

  • Page 4: Safety

    Safety Safety definitions • Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Warnings, cautions and notes are used to point out Keep cord away from heat, oil, sharp edges or specially important parts of the manual. moving parts.
  • Page 5 exposure in the actual conditions of use (taking Liquid ejected from the battery may cause irritations account of all parts of the operating cycle such as or burns. the times when the tool is switched off and when it is Service running idle in addition to the trigger).
  • Page 6 other persons not trained in the use of the product • Always inspect the working area. Remove all loose and/or the battery to use or service it. Local laws objects such as stones, broken glass, nails, steel may regulate the age of the user. wire, string, etc., that could be thrown out or become wrapped around the cutting attachment.
  • Page 7 Personal protective equipment • Use gloves when necessary, for example when you attach, examine or clean the cutting equipment. WARNING: Read the warning instructions that follow before you use the product. • Always use approved personal protective equipment when you use the product. Personal protective equipment cannot fully prevent injury but it decreases the degree of injury if an accident does occur.
  • Page 8 3. Push the power trigger up and apply full power. CAUTION: All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below you must contact your service agent.
  • Page 9 • Use the BLi battery that is rechargable as a power the battery outdoors. Do not charge the battery in supply for the related Husqvarna products only. To wet conditions. prevent injury, do not use the battery as a power •...

  • Page 10: Assembly

    To connect the battery to the product WARNING: Only use the original Husqvarna battery in the product. 1. Fully charge the battery. 2. Put the battery into the battery holder of the product.
  • Page 11 To start the product 2. Put the battery in the battery charger. 1. Push and hold the start/stop button until the green LED comes on. 3. Make sure that the green charging light on the battery charger comes on. That means that the battery is connected correctly to the battery charger.

  • Page 12: Maintenance

    3. Make sure that the motor does not touch the hedge. 4. Hold the product near your body for a stable work WARNING: Do not operate the cutting position. attachment when you adjust the handle. 5. Make sure that the tip of the cutting equipment does To stop the product not touch the ground.
  • Page 13 Maintenance schedule The following is a list of the maintenance steps that you must do on the product. WARNING: Remove the battery before you do maintenance. Maintenance Before Weekly Monthly Clean the external parts of the product. Examine that the start and stop switch works correctly and is not damaged. Make sure that the power trigger and the power trigger lockout function correctly from a safety point of view.

  • Page 14: Troubleshooting

    Troubleshooting Keypad Problem Possible faults Possible solution Green start LED Low battery voltage. Charge the battery. flashes. Red error LED flash- Overload. The cutting attachment is blocked. stop the product. Remove the battery. Clean the cut- ting attachment from unwanted materials. Loosen the chain.

  • Page 15: Transportation, Storage And Disposal

    Note: The symbol shows on the product or package of storage for long periods. the product. • Put the battery charger in storage in a space that is closed and dry. Technical data Technical data 520iHD60 520iHD70 Motor Motor type PMDC (4- PMDC (4- brush) brush)
  • Page 16 Frequency, Hz 50-60 50-60 Power, W The Husqvarna Handheld Battery products marked with IPX4 fulfils these requirements on product approval level Noise emissions in the environment measured as sound power (L ) in conformity with EC directive 2000/14/EC. The difference between guaranteed and measured sound power is that guaranteed sound power also includes dispersion in the measurement result and the variations between different products of the same model refer to Directive 2000/14/EC.

  • Page 17: Ec Declaration Of Conformity

    EC Declaration of Conformity EC Declaration of conformity Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the hedge trimmers Husqvarna 520iHD60, 520iHD70 with serial numbers dating from 2018 onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:...
  • Page 18 773 - 002 -...
  • Page 19 773 - 002 -...
  • Page 20 Original instructions 1140370-26 2018-11-12...

This manual is also suitable for:

520ihd70

Table of Contents