Sealey SA6006 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instruction protection
manual
1. SAFETY
WARNING! DO NOT use wrench if damaged or thought to be faulty. contact service Agent.
‰
WARNING! disconnect from the air supply before changing accessories or servicing.
‰
WARNING! due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we recommend
‰
you wear suitable respiratory protection.
WARNING! check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
DO NOT use the wrench for a task it is not designed to perform.
8
DO NOT use worn, or damaged sockets
8
DO NOT use the wrench unless you have been instructed in its use by a qualified person.
8
DO NOT use the wrench for a task it is not designed to perform.
8
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
8
DO NOT operate the wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry the wrench with your hand on the power trigger in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts
9
may be dangerous and will invalidate the warranty.
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are
9
secure.
Only use impact sockets which are specifically designed for use with an impact wrench.
9
Wear approved safety eye/face shield, ear defenders and hand protection.
9
follow all workshop safety rules, regulations, and conditions when using the wrench.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non essential persons away from the working area.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. INTRODuCTION
twin hammer design gives the wrench a high torque output making it suitable for jobs that would normally require a 3/4" impact wrench. Push
button style forward/reverse switch enables one handed operation. two stage trigger design offers increased control with feather touch trigger for
running up to 272nm and fully depressed for full torque. features hammer cage support mechanism to reduce tool vibration while in operation.
composite casing with soft grip makes the tool lighter, easier to handle and helps to reduce vibration and chill. Handle exhaust with built-in
silencer to help reduce noise level and limits circulation of brake dust on wheel applications. suitable for heavy-duty use in the professional
garage.
3. SPECIFICATION
model no: .................................................................. sA6006
drive: .......................................................................... 1/2" sq
Working torque: ..........................................800lb.ft (1088nm)
maximum torque: .......................................950lb.ft (1288nm)
ultimate torque: ........................................1050lb.ft (1428nm)
free speed: .............................................................. 7000rpm
Air consumption: ......................................................... 9.5cfm
operating pressure: ...................................................... 90psi
inlet size: ...................................................................1/4"BsP
Weight: .......................................................................... 2.1kg
noise power/pressure: ....................................... 110/99dB(A)
Vibration/uncertainty: ....................................... 4.45/0.94m/s²
© Jack sealey limited
instructions for
COMPOSITE AIR IMPACT WRENCH 1/2" Sq.
DRIVE TWIN HAMMER
model no:
Wear ear Wear protective
protection gloves
Original Language Version
SA6006
sA6006 |issue :2 (H,f) 10/11/17