Sealey SA602L Instructions For Use

Thank you for purchasing a Sealey product . Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance .
IMPORTANT: PLeASe ReAD THeSe INSTRUCTIONS CARefULLy . NOTe THe SAfe OPeRATIONAL ReQUIReMeNTS, WARNINGS & CAUTIONS . USe THe
PRODUCT CORReCTLy AND WITH CARe fOR THe PURPOSe fOR WHICH IT IS INTeNDeD . fAILURe TO DO SO MAy CAUSe DAMAGe AND/OR
PeRSONAL INJURy AND WILL INVALIDATe THe WARRANTy . KeeP THeSe INSTRUCTIONS SAfe fOR fUTURe USe .
1 . SAfeTy
Wear ear
Wear eye
Protection
Protection
 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
 WARNING! Disconnect from air supply before changing accessories or servicing.
 Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
 WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
 Only use impact sockets which are specifically designed for use with an impact wrench.
 Wear approved safety eye/face shield, ear defenders, and hand protection.
 WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we recommend
you wear suitable respiratory protection
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 When not in use disconnect from air supply and store in a safe, dry, childproof location.
 Keep children and non essential persons away from the working area.
 DO NOT use the wrench for a task it is not designed to perform.
 WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
 DO NOT use wrench unless you have been instructed in its use by a qualified person.
 DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
 DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT carry wrench with your hand on the power trigger, in order to avoid unintentional starting.
 DO NOT direct air from the air hose at yourself or others.
 DO NOT use worn or damaged sockets.
2 . INTRODUCTION
Powerful 1/2"Sq drive impact wrench, long anvil with twin hammer mechanism for increased torque. Air motor features quality bearings, steel
end plates and carefully finished components to ensure smooth running and maximum power. Combination forward/reverse and speed
selector. Suitable for heavy tyre shop use.
3 . SPeCIfICATION
Model No: . . . . . . . . . . . . . . . . . . . . . .SA602L
Drive size:. . . . . . . . . . . . . . . . . . . . . . . .1/2''Sq
Working Torque: . . . . . . . . . . . . 400lb.ft/544Nm
Max torque: . . . . . . . . . . . . . . . 480lb.ft/653Nm
Ultimate torque: . . . . . . . . . . . . 500lb.ft/680Nm
Free Speed: . . . . . . . . . . . . . . . . . . . . 7500rpm
Air consumption:. . . . . . . . . . . . . . . . . . . 4.2cfm
Operating pressure: . . . . . . . . . . . . . . . . . 90psi
Air inlet: . . . . . . . . . . . . . . . . . . . . . . .1/4"BSP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . 2.82kg
4 . PRePARATION
4 .1 Air Supply
4.1.1. recommended hook-up procedure is shown in fig.1.
4.1.2. Ensure wrench air valve, or trigger, is in the OFF position before connecting it to air supply.
4.1.3. You will require an air pressure of 90psi, and an air flow according to specification.
WARNING! Ensure the air supply is clean and does not exceed 90psi whilst operating the wrench. Too high an air pressure and

unclean air will shorten the product life due to excessive wear, and may be dangerous, causing damage and/or personal injury.
4.1.4. Drain the air tank daily. Water in the air line will damage the wrench.
4.1.5. Clean the air inlet filter weekly.
4.1.6. line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
¼" I.D. and fittings must have the same inside dimensions.
4.1.7. Keep the hose away from heat, oil and sharp edges. Check the hose for wear and make certain that all connections are secure.
4 .2 . Couplings
4.2.1. Vibration may cause failure if a quick change coupling is connected directly to the wrench. To overcome this, connect a leader hose to
the wrench. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. refer to figs.1 and 2.
© Jack Sealey limited
INSTrUCTIONS FOr:
AIR IMPACT WReNCH 1/2" SQ . DRIVe
TWIN HAMMeR - LONG ANVIL
MODEl NO:
Wear
Wear Respiratory
Gloves
Protection
Vibration: . . . . . . . . . . . . . . . . . . . .. 5.47m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . 1.5m/s²
Noise power: . . . . . . . . . . . . . . . . . .103dB(A)
Noise pressure: . . . . . . . . . . . . . . . . . 92dB(A)
Original Language Version
SA602L
SA602l Issue: 2(SP) - 21/05/14